Added missing #endif

Create readmdFrench.md

Contributors.md

@@ -18,7 +18,5 @@ These are the active contributors of this project that you may contact if there
 - [philipphenkel](https://github.com/philipphenkel): Active Contributor
 - [MCUdude](https://github.com/MCUdude): Contributor
 - [marcmerlin](https://github.com/marcmerlin): Contributor (ESP32 port)
-- [bengtmartensson](https://github.com/bengtmartensson): Active Contributor
-- [MrBryonMiller](https://github.com/MrBryonMiller): Contributor
 
 Note: This list is being updated constantly so please let [z3t0](https://github.com/z3t0) know if you have been missed.

IRremote.cpp

@@ -20,10 +20,11 @@
 
 // Defining IR_GLOBAL here allows us to declare the instantiation of global variables
 #define IR_GLOBAL
-#include "IRremote.h"
+#	include "IRremote.h"
+#	include "IRremoteInt.h"
 #undef IR_GLOBAL
 
-#ifdef HAS_AVR_INTERRUPT_H
+#ifndef IR_TIMER_USE_ESP32
 #include <avr/interrupt.h>
 #endif
 
@@ -51,12 +52,11 @@ int  MATCH (int measured,  int desired)
  	DBG_PRINT(TICKS_HIGH(desired), DEC);
 
   bool passed = ((measured >= TICKS_LOW(desired)) && (measured <= TICKS_HIGH(desired)));
-  if (passed) {
+  if (passed)
     DBG_PRINTLN(F("?; passed"));
-  } else {
+  else
     DBG_PRINTLN(F("?; FAILED")); 
-  }
+ 	return passed;
-  return passed;
 }
 
 //+========================================================
@@ -78,12 +78,11 @@ int  MATCH_MARK (int measured_ticks,  int desired_us)
 
   bool passed = ((measured_ticks >= TICKS_LOW (desired_us + MARK_EXCESS))
                 && (measured_ticks <= TICKS_HIGH(desired_us + MARK_EXCESS)));
-  if (passed) {
+  if (passed)
     DBG_PRINTLN(F("?; passed"));
-  } else {
+  else
     DBG_PRINTLN(F("?; FAILED")); 
-  }
+ 	return passed;
-  return passed;
 }
 
 //+========================================================
@@ -105,12 +104,11 @@ int  MATCH_SPACE (int measured_ticks,  int desired_us)
 
   bool passed = ((measured_ticks >= TICKS_LOW (desired_us - MARK_EXCESS))
                 && (measured_ticks <= TICKS_HIGH(desired_us - MARK_EXCESS)));
-  if (passed) {
+  if (passed)
     DBG_PRINTLN(F("?; passed"));
-  } else {
+  else
     DBG_PRINTLN(F("?; FAILED")); 
-  }
+ 	return passed;
-  return passed;
 }
 
 //+=============================================================================
@@ -125,7 +123,11 @@ int  MATCH_SPACE (int measured_ticks,  int desired_us)
 // As soon as first MARK arrives:
 //   Gap width is recorded; Ready is cleared; New logging starts
 //
+#ifdef IR_TIMER_USE_ESP32
+void IRTimer()
+#else
 ISR (TIMER_INTR_NAME)
+#endif
 {
 	TIMER_RESET;
 
@@ -187,7 +189,6 @@ ISR (TIMER_INTR_NAME)
 		 	break;
 	}
 
-#ifdef BLINKLED
 	// If requested, flash LED while receiving IR data
 	if (irparams.blinkflag) {
 		if (irdata == MARK)
@@ -196,5 +197,4 @@ ISR (TIMER_INTR_NAME)
 		else if (irparams.blinkpin) digitalWrite(irparams.blinkpin, LOW); // Turn user defined pin LED on
 				else BLINKLED_OFF() ;   // if no user defined LED pin, turn default LED pin for the hardware on
 	}
-#endif // BLINKLED
 }

IRremote.h

@@ -1,7 +1,3 @@
-/**
- * @file IRremote.h
- * @brief Public API to the library.
- */
 
 //******************************************************************************
 // IRremote
@@ -25,7 +21,7 @@
 //------------------------------------------------------------------------------
 // The ISR header contains several useful macros the user may wish to use
 //
-#include "private/IRremoteInt.h"
+#include "IRremoteInt.h"
 
 //------------------------------------------------------------------------------
 // Supported IR protocols
@@ -83,6 +79,9 @@
 #define DECODE_LEGO_PF       0 // NOT WRITTEN
 #define SEND_LEGO_PF         1
 
+#define DECODE_NERF_LOP      0 // NOT WRITTEN
+#define SEND_NERF_LOP        1
+
 //------------------------------------------------------------------------------
 // When sending a Pronto code we request to send either the "once" code
 //                                                   or the "repeat" code
@@ -98,10 +97,10 @@
 #define PRONTO_FALLBACK    true
 #define PRONTO_NOFALLBACK  false
 
-/**
+//------------------------------------------------------------------------------
- * An enum consisting of all supported formats.
+// An enumerated list of all supported formats
- * You do NOT need to remove entries from this list when disabling protocols!
+// You do NOT need to remove entries from this list when disabling protocols!
- */
+//
 typedef
 	enum {
 		UNKNOWN      = -1,
@@ -123,12 +122,13 @@ typedef
 		DENON,
 		PRONTO,
 		LEGO_PF,
+	        NERF_LOP,
 	}
 decode_type_t;
 
-/**
+//------------------------------------------------------------------------------
- * Set DEBUG to 1 for lots of lovely debug output.
+// Set DEBUG to 1 for lots of lovely debug output
- */
+//
 #define DEBUG  0
 
 //------------------------------------------------------------------------------
@@ -138,13 +138,7 @@ decode_type_t;
 #	define DBG_PRINT(...)    Serial.print(__VA_ARGS__)
 #	define DBG_PRINTLN(...)  Serial.println(__VA_ARGS__)
 #else
-/**
- * If DEBUG, print the arguments, otherwise do nothing.
- */
 #	define DBG_PRINT(...)
-/**
- * If DEBUG, print the arguments as a line, otherwise do nothing.
- */
 #	define DBG_PRINTLN(...)
 #endif
 
@@ -155,71 +149,39 @@ int  MATCH       (int measured, int desired) ;
 int  MATCH_MARK  (int measured_ticks, int desired_us) ;
 int  MATCH_SPACE (int measured_ticks, int desired_us) ;
 
-/**
+//------------------------------------------------------------------------------
- * Results returned from the decoder
+// Results returned from the decoder
- */
+//
 class decode_results
 {
 	public:
-		decode_type_t          decode_type;  ///< UNKNOWN, NEC, SONY, RC5, ...
+		decode_type_t          decode_type;  // UNKNOWN, NEC, SONY, RC5, ...
-		unsigned int           address;      ///< Used by Panasonic & Sharp [16-bits]
+		unsigned int           address;      // Used by Panasonic & Sharp [16-bits]
-		unsigned long          value;        ///< Decoded value [max 32-bits]
+		unsigned long          value;        // Decoded value [max 32-bits]
-		int                    bits;         ///< Number of bits in decoded value
+		int                    bits;         // Number of bits in decoded value
-		volatile unsigned int  *rawbuf;      ///< Raw intervals in 50uS ticks
+		volatile unsigned int  *rawbuf;      // Raw intervals in 50uS ticks
-		int                    rawlen;       ///< Number of records in rawbuf
+		int                    rawlen;       // Number of records in rawbuf
-		int                    overflow;     ///< true iff IR raw code too long
+		int                    overflow;     // true iff IR raw code too long
 };
 
-/**
+//------------------------------------------------------------------------------
- * Decoded value for NEC when a repeat code is received
+// Decoded value for NEC when a repeat code is received
- */
+//
 #define REPEAT 0xFFFFFFFF
 
-/**
+//------------------------------------------------------------------------------
- * Main class for receiving IR
+// Main class for receiving IR
- */
+//
 class IRrecv
 {
 	public:
-                /**
-                 * Instantiate the IRrecv class. Multiple instantiation is not supported.
-                 * @param recvpin Arduino pin to use. No sanity check is made.
-                 */
 		IRrecv (int recvpin) ;
-                /**
-                 * Instantiate the IRrecv class. Multiple instantiation is not supported.
-                 * @param recvpin Arduino pin to use, where a demodulating IR receiver is connected.
-                 * @param blinkpin pin to blink when receiving IR. Not supported by all hardware. No sanity check is made.
-                 */
 		IRrecv (int recvpin, int blinkpin);
 
-                /**
-                 * TODO: Why is this public???
-                 * @param blinkflag
-                 */
 		void  blink13    (int blinkflag) ;
-
-                /**
-                 * Attempt to decode the recently receive IR signal
-                 * @param results decode_results instance returning the decode, if any.
-                 * @return success of operation. TODO: convert to bool
-                 */
 		int   decode     (decode_results *results) ;
-
-                /**
-                 * Enable IR reception.
-                 */
 		void  enableIRIn ( ) ;
-
-                /**
-                 * Returns status of reception
-                 * @return true if no reception is on-going.
-                 */
 		bool  isIdle     ( ) ;
-
-                /**
-                 * Called to re-enable IR reception.
-                 */
 		void  resume     ( ) ;
 
 	private:
@@ -228,17 +190,10 @@ class IRrecv
 
 		//......................................................................
 #		if (DECODE_RC5 || DECODE_RC6)
-			/**
+			// This helper function is shared by RC5 and RC6
-                         *  This helper function is shared by RC5 and RC6
-                         */
 			int  getRClevel (decode_results *results,  int *offset,  int *used,  int t1) ;
 #		endif
 #		if DECODE_RC5
-                        /**
-                         * Try to decode the recently received IR signal as an RC5 signal-
-                         * @param results decode_results instance returning the decode, if any.
-                         * @return Success of the operation.
-                         */
 			bool  decodeRC5        (decode_results *results) ;
 #		endif
 #		if DECODE_RC6
@@ -300,26 +255,19 @@ class IRrecv
 #		if DECODE_LEGO_PF
 			bool  decodeLegoPowerFunctions (decode_results *results) ;
 #		endif
+//......................................................................
+#		if DECODE_NERF_LOP
+			bool  decodeNerfLOP (decode_results *results) ;
+#               endif
 } ;
 
-/**
+//------------------------------------------------------------------------------
- * Main class for sending IR
+// Main class for sending IR
- */
+//
 class IRsend
 {
 	public:
-#ifdef USE_SOFT_CARRIER
+		IRsend () { }
-
-		IRsend(int pin = SEND_PIN)
-		{
-			sendPin = pin;
-		}
-#else
-
-		IRsend()
-		{
-		}
-#endif
 
 		void  custom_delay_usec (unsigned long uSecs);
 		void  enableIROut 		(int khz) ;
@@ -330,7 +278,6 @@ class IRsend
 		//......................................................................
 #		if SEND_RC5
 			void  sendRC5        (unsigned long data,  int nbits) ;
-			void  sendRC5ext     (unsigned long addr, unsigned long cmd, boolean toggle);
 #		endif
 #		if SEND_RC6
 			void  sendRC6        (unsigned long data,  int nbits) ;
@@ -400,20 +347,10 @@ class IRsend
 #		if SEND_LEGO_PF
 			void  sendLegoPowerFunctions (uint16_t data, bool repeat = true) ;
 #		endif
-
+//......................................................................
-#ifdef USE_SOFT_CARRIER
+#		if SEND_NERF_LOP
-	private:
+			void  sendNerfLOP (uint16_t data, bool repeat = true) ;
-		int sendPin;
+#               endif
-
-		unsigned int periodTime;
-		unsigned int periodOnTime;
-
-		void sleepMicros(unsigned long us);
-		void sleepUntilMicros(unsigned long targetTime);
-
-#else
-		const int sendPin = SEND_PIN;
-#endif
 } ;
 
 #endif

IRremoteInt.h

@@ -18,9 +18,15 @@
 #define IRremoteint_h
 
 //------------------------------------------------------------------------------
-// Include the Arduino header
+// Include the right Arduino header
 //
-#include <Arduino.h>
+#if defined(ARDUINO) && (ARDUINO >= 100)
+#	include <Arduino.h>
+#else
+#	if !defined(IRPRONTO)
+#		include <WProgram.h>
+#	endif
+#endif
 
 //------------------------------------------------------------------------------
 // This handles definition and access to global variables
@@ -34,22 +40,19 @@
 //------------------------------------------------------------------------------
 // Information for the Interrupt Service Routine
 //
-#define RAWBUF  101  ///< Maximum length of raw duration buffer. Must be odd.
+#define RAWBUF  101  // Maximum length of raw duration buffer
 
-/**
-  * This struct is used to communicate with the ISR (interrupt service routine).
-  */
 typedef
 	struct {
 		// The fields are ordered to reduce memory over caused by struct-padding
-		uint8_t       rcvstate;        ///< State Machine state
+		uint8_t       rcvstate;        // State Machine state
-		uint8_t       recvpin;         ///< Pin connected to IR data from detector
+		uint8_t       recvpin;         // Pin connected to IR data from detector
 		uint8_t       blinkpin;
-		uint8_t       blinkflag;       ///< true -> enable blinking of pin on IR processing
+		uint8_t       blinkflag;       // true -> enable blinking of pin on IR processing
-		uint8_t       rawlen;          ///< counter of entries in rawbuf
+		uint8_t       rawlen;          // counter of entries in rawbuf
-		unsigned int  timer;           ///< State timer, counts 50uS ticks.
+		unsigned int  timer;           // State timer, counts 50uS ticks.
-		unsigned int  rawbuf[RAWBUF];  ///< raw data
+		unsigned int  rawbuf[RAWBUF];  // raw data
-		uint8_t       overflow;        ///< Raw buffer overflow occurred
+		uint8_t       overflow;        // Raw buffer overflow occurred
 	}
 irparams_t;
 
@@ -60,11 +63,9 @@ irparams_t;
 #define STATE_STOP      5
 #define STATE_OVERFLOW  6
 
-/**
+// Allow all parts of the code access to the ISR data
- * Allow all parts of the code access to the ISR data
+// NB. The data can be changed by the ISR at any time, even mid-function
- * NB. The data can be changed by the ISR at any time, even mid-function
+// Therefore we declare it as "volatile" to stop the compiler/CPU caching it
- * Therefore we declare it as "volatile" to stop the compiler/CPU caching it
- */
 EXTERN  volatile irparams_t  irparams;
 
 //------------------------------------------------------------------------------
@@ -84,12 +85,8 @@ EXTERN  volatile irparams_t  irparams;
 // Pulse parameters in uSec
 //
 
-/**
+// Due to sensor lag, when received, Marks  tend to be 100us too long and
- * When received, marks  tend to be too long and
+//                                   Spaces tend to be 100us too short
- * spaces tend to be too short.
- * To compensate for this, MARK_EXCESS is subtracted from all marks,
- * and added to all spaces.
- */
 #define MARK_EXCESS    100
 
 // Upper and Lower percentage tolerances in measurements

README.md

@@ -8,7 +8,7 @@ This library enables you to send and receive using infra-red signals on an Ardui
 
 Tutorials and more information will be made available on [the official homepage](http://z3t0.github.io/Arduino-IRremote/).
 
-## Version - 2.5.0b
+## Version - 2.2.3
 
 ## Installation
 1. Navigate to the [Releases](https://github.com/z3t0/Arduino-IRremote/releases) page.
@@ -33,6 +33,7 @@ Whether you use the Adafruit Neopixel lib, or FastLED, interrupts get disabled o
 - ATtiny 84 / 85
 - ESP32 (receive only)
 - ESP8266 is supported in a fork based on an old codebase that isn't as recent, but it works reasonably well given that perfectly timed sub millisecond interrupts are different on that chip. See https://github.com/markszabo/IRremoteESP8266
+- Sparkfun Pro Micro
 
 We are open to suggestions for adding support to new boards, however we highly recommend you contact your supplier first and ask them to provide support from their side.
 
@@ -43,7 +44,7 @@ We are open to suggestions for adding support to new boards, however we highly r
 | [ATtiny84](https://github.com/SpenceKonde/ATTinyCore)                    | **6**               | **1**             |
 | [ATtiny85](https://github.com/SpenceKonde/ATTinyCore)                    | **1**               | **TINY0**         |
 | [ATmega8](https://github.com/MCUdude/MiniCore)                           | **9**               | **1**             |
-| Atmega32u4                                                               | 5, **9**, 13        | 1, 3, **4**       |
+| Atmega32u4                                                               | 5, 9, **13**        | 1, 3, **4**       |
 | [ATmega48, ATmega88, ATmega168, ATmega328](https://github.com/MCUdude/MiniCore) | **3**, 9     | 1, **2**          |
 | [ATmega1284](https://github.com/MCUdude/MightyCore)                      | 13, 14, 6           | 1, **2**, 3       |
 | [ATmega164, ATmega324, ATmega644](https://github.com/MCUdude/MightyCore) | 13, **14**          | 1, **2**          |
@@ -51,6 +52,7 @@ We are open to suggestions for adding support to new boards, however we highly r
 | [ATmega64, ATmega128](https://github.com/MCUdude/MegaCore)               | **13**              | **1**             |
 | ATmega1280, ATmega2560                                                   | 5, 6, **9**, 11, 46 | 1, **2**, 3, 4, 5 |
 | [ESP32](http://esp32.net/)                                               | N/A (not supported) | **1**             |
+| [Sparkfun Pro Micro](https://www.sparkfun.com/products/12640)            | 9, **5**, 5         | 1, **3**, 4_HS    |
 | [Teensy 1.0](https://www.pjrc.com/teensy/)                               | **17**              | **1**             |
 | [Teensy 2.0](https://www.pjrc.com/teensy/)                               | 9, **10**, 14       | 1, 3, **4_HS**    |
 | [Teensy++ 1.0 / 2.0](https://www.pjrc.com/teensy/)                       | **1**, 16, 25       | 1, **2**, 3       |
@@ -68,20 +70,6 @@ The table above lists the currently supported timers and corresponding send pins
 ## Usage
 - TODO (Check examples for now)
 
-## API documentation
-This project documents the library API using [Doxygen](http://www.doxygen.org).
-It is planned to make generated and up-to-date API documentation available online.
-
-To generate the API documentation,
-Doxygen, as well as [Graphviz](http://www.graphviz.org/) should be installed.
-(Note that on Windows, it may be necessary to add the Graphviz binary directory
-(something like `C:\Program Files\Graphviz2.38\bin`)
-to the `PATH` variable manually.)
-With Doxygen and Graphviz installed, issue the command
-`doxygen` from the command line in the main project directory, which will
-generate the API documentation in HTML format.
-The just generated `api-doc/index.html` can now be opened in a browser.
-
 ## Contributing
 If you want to contribute to this project:
 - Report bugs and errors

arduino-irremote.sublime-workspace

@@ -0,0 +1,240 @@
+{
+	"auto_complete":
+	{
+		"selected_items":
+		[
+			[
+				"vb",
+				"vboMatrix"
+			]
+		]
+	},
+	"buffers":
+	[
+	],
+	"build_system": "",
+	"build_system_choices":
+	[
+	],
+	"build_varint": "",
+	"command_palette":
+	{
+		"height": 275.0,
+		"last_filter": "blame",
+		"selected_items":
+		[
+			[
+				"blame",
+				"Git: Blame"
+			],
+			[
+				"install",
+				"Package Control: Install Package"
+			],
+			[
+				"diff",
+				"Git: Diff Current File"
+			],
+			[
+				"js",
+				"Set Syntax: JavaScript"
+			],
+			[
+				"i",
+				"Package Control: Install Package"
+			],
+			[
+				"instal",
+				"Package Control: Install Package"
+			]
+		],
+		"width": 510.0
+	},
+	"console":
+	{
+		"height": 126.0,
+		"history":
+		[
+			"import urllib.request,os,hashlib; h = '2915d1851351e5ee549c20394736b442' + '8bc59f460fa1548d1514676163dafc88'; pf = 'Package Control.sublime-package'; ipp = sublime.installed_packages_path(); urllib.request.install_opener( urllib.request.build_opener( urllib.request.ProxyHandler()) ); by = urllib.request.urlopen( 'http://packagecontrol.io/' + pf.replace(' ', '%20')).read(); dh = hashlib.sha256(by).hexdigest(); print('Error validating download (got %s instead of %s), please try manual install' % (dh, h)) if dh != h else open(os.path.join( ipp, pf), 'wb' ).write(by)"
+		]
+	},
+	"distraction_free":
+	{
+		"menu_visible": true,
+		"show_minimap": false,
+		"show_open_files": false,
+		"show_tabs": false,
+		"side_bar_visible": false,
+		"status_bar_visible": false
+	},
+	"expanded_folders":
+	[
+		"/C/Users/Rafi Khan/Documents/Arduino/libraries/Arduino-IRremote"
+	],
+	"file_history":
+	[
+		"/C/Users/Rafi Khan/Documents/Arduino/libraries/Arduino-IRremote/changelog.md",
+		"/C/Users/Rafi Khan/Documents/Development/Arduino-IRremote/arduino-irremote.sublime-project",
+		"/C/Users/Rafi Khan/Documents/Development/Arduino-IRremote/.gitignore",
+		"/C/Users/Rafi Khan/Documents/Development/magic/README.md",
+		"/C/Users/Rafi Khan/Documents/Development/magic/shader.frag",
+		"/C/Users/Rafi Khan/Documents/Development/magic/package.json",
+		"/C/Users/Rafi Khan/Documents/Development/magic/block.js",
+		"/C/Users/Rafi Khan/Documents/Development/magic/chunker.js",
+		"/C/Users/Rafi Khan/Documents/Development/magic/index.js",
+		"/C/Users/Rafi Khan/Documents/Development/magic/blocks",
+		"/C/Users/Rafi Khan/AppData/Roaming/Sublime Text 3/Packages/User/Preferences.sublime-settings",
+		"/C/Users/Rafi Khan/Documents/Development/magic/shader.vert",
+		"/C/Users/Rafi Khan/Documents/Development/magic/magic.sublime-project",
+		"/C/Users/Rafi Khan/Documents/Development/magic/node_modules/browserify/node_modules/syntax-error/node_modules/acorn/.tern-project",
+		"/C/Users/Rafi Khan/OneDrive/Documents/School-RafiKhan/Grade 11/CS30/Python/supermarket.py",
+		"/C/Users/Rafi Khan/OneDrive/Documents/School-RafiKhan/Grade 11/CS30/Python/takingavacation.py",
+		"/C/Users/Rafi Khan/OneDrive/Documents/School-RafiKhan/Grade 11/CS30/Python/TipCalculator.py",
+		"/C/Users/Rafi Khan/OneDrive/Documents/School-RafiKhan/Grade 11/CS30/Python/battleship.py",
+		"/C/Users/Rafi Khan/OneDrive/Documents/School-RafiKhan/Grade 11/CS30/Python/exam.py",
+		"/C/Users/Rafi Khan/OneDrive/Documents/School-RafiKhan/Grade 11/CS30/Python/pyglatin.py",
+		"/C/Users/Rafi Khan/OneDrive/Documents/School-RafiKhan/Grade 11/CS30/Python/student.py"
+	],
+	"find":
+	{
+		"height": 28.0
+	},
+	"find_in_files":
+	{
+		"height": 0.0,
+		"where_history":
+		[
+		]
+	},
+	"find_state":
+	{
+		"case_sensitive": false,
+		"find_history":
+		[
+			"i",
+			"Direction",
+			";",
+			";\n",
+			"north",
+			"cubeMatrix",
+			")\n",
+			"vec3.set",
+			"f",
+			";",
+			"();\n",
+			"render",
+			"this",
+			"y"
+		],
+		"highlight": true,
+		"in_selection": false,
+		"preserve_case": false,
+		"regex": false,
+		"replace_history":
+		[
+		],
+		"reverse": false,
+		"show_context": true,
+		"use_buffer2": true,
+		"whole_word": false,
+		"wrap": true
+	},
+	"groups":
+	[
+		{
+			"sheets":
+			[
+			]
+		}
+	],
+	"incremental_find":
+	{
+		"height": 28.0
+	},
+	"input":
+	{
+		"height": 66.0
+	},
+	"layout":
+	{
+		"cells":
+		[
+			[
+				0,
+				0,
+				1,
+				1
+			]
+		],
+		"cols":
+		[
+			0.0,
+			1.0
+		],
+		"rows":
+		[
+			0.0,
+			1.0
+		]
+	},
+	"menu_visible": true,
+	"output.find_results":
+	{
+		"height": 0.0
+	},
+	"pinned_build_system": "",
+	"project": "arduino-irremote.sublime-project",
+	"replace":
+	{
+		"height": 52.0
+	},
+	"save_all_on_build": true,
+	"select_file":
+	{
+		"height": 0.0,
+		"last_filter": "",
+		"selected_items":
+		[
+			[
+				"json",
+				"package.json"
+			],
+			[
+				"inde",
+				"index.js"
+			]
+		],
+		"width": 0.0
+	},
+	"select_project":
+	{
+		"height": 0.0,
+		"last_filter": "",
+		"selected_items":
+		[
+		],
+		"width": 0.0
+	},
+	"select_symbol":
+	{
+		"height": 0.0,
+		"last_filter": "",
+		"selected_items":
+		[
+		],
+		"width": 0.0
+	},
+	"selected_group": 0,
+	"settings":
+	{
+	},
+	"show_minimap": true,
+	"show_open_files": false,
+	"show_tabs": true,
+	"side_bar_visible": true,
+	"side_bar_width": 150.0,
+	"status_bar_visible": true,
+	"template_settings":
+	{
+	}
+}

boarddefs.h

@@ -15,37 +15,13 @@
 //
 // JVC and Panasonic protocol added by Kristian Lauszus (Thanks to zenwheel and other people at the original blog post)
 // Whynter A/C ARC-110WD added by Francesco Meschia
+
+// Sparkfun Pro Micro support by Alastair McCormack
 //******************************************************************************
 
 #ifndef boarddefs_h
 #define boarddefs_h
 
-// Define some defaults, that some boards may like to override
-// (This is to avoid negative logic, ! DONT_... is just awkward.)
-
-// This board has/needs the avr/interrupt.h
-#define HAS_AVR_INTERRUPT_H
-
-// Define if sending is supported
-#define SENDING_SUPPORTED
-
-// If defined, a standard enableIRIn function will be define.
-// Undefine for boards supplying their own.
-#define USE_DEFAULT_ENABLE_IR_IN
-
-// Duty cycle in percent for sent signals. Presently takes effect only with USE_SOFT_CARRIER
-#define DUTY_CYCLE 50
-
-// If USE_SOFT_CARRIER, this amount (in micro seconds) is subtracted from the
-// on-time of the pulses.
-#define PULSE_CORRECTION 3
-
-// digitalWrite is supposed to be slow. If this is an issue, define faster,
-// board-dependent versions of these macros SENDPIN_ON(pin) and SENDPIN_OFF(pin).
-// Portable, possibly slow, default definitions are given at the end of this file.
-// If defining new versions, feel free to ignore the pin argument if it
-// is not configurable on the current board.
-
 //------------------------------------------------------------------------------
 // Defines for blinking the LED
 //
@@ -65,31 +41,11 @@
 #	define BLINKLED_ON()   (PORTD |= B00000001)
 #	define BLINKLED_OFF()  (PORTD &= B11111110)
 
-#elif defined(ARDUINO_ARCH_SAM) || defined(ARDUINO_ARCH_SAMD)
+// No system LED on ESP32, disable blinking
-#	define BLINKLED        LED_BUILTIN
-#	define BLINKLED_ON()   (digitalWrite(LED_BUILTIN, HIGH))
-#	define BLINKLED_OFF()  (digitalWrite(LED_BUILTIN, LOW))
-
-#	define USE_SOFT_CARRIER
-	// Define to use spin wait instead of delayMicros()
-//#	define USE_SPIN_WAIT
-#       undef USE_DEFAULT_ENABLE_IR_IN
-
-        // The default pin used used for sending.
-#	define SEND_PIN 9
-
 #elif defined(ESP32)
-        // No system LED on ESP32, disable blinking by NOT defining BLINKLED
+#	define BLINKLED        255
-
+#	define BLINKLED_ON()   1
-        // avr/interrupt.h is not present
+#	define BLINKLED_OFF()  1
-#       undef HAS_AVR_INTERRUPT_H
-
-        // Sending not implemented
-#       undef SENDING_SUPPORTED
-
-        // Supply own enbleIRIn
-#       undef USE_DEFAULT_ENABLE_IR_IN
-
 #else
 #	define BLINKLED        13
 #	define BLINKLED_ON()  (PORTB |= B00100000)
@@ -116,8 +72,14 @@
 //   switch IRremote to use a different timer.
 //
 
+// Sparkfun Pro Micro
+#if defined(ARDUINO_AVR_PROMICRO)
+	//#define IR_USE_TIMER1     // tx = pin 9
+	#define IR_USE_TIMER3       // tx = pin 5
+	//#define IR_USE_TIMER4_HS  // tx = pin 5
+
 // Arduino Mega
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
+#elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
 	//#define IR_USE_TIMER1   // tx = pin 11
 	#define IR_USE_TIMER2     // tx = pin 9
 	//#define IR_USE_TIMER3   // tx = pin 5
@@ -131,8 +93,8 @@
 // Teensy 2.0
 #elif defined(__AVR_ATmega32U4__)
 	//#define IR_USE_TIMER1   // tx = pin 14
-	#define IR_USE_TIMER3   // tx = pin 9
+	//#define IR_USE_TIMER3   // tx = pin 9
-	//#define IR_USE_TIMER4_HS  // tx = pin 10
+	#define IR_USE_TIMER4_HS  // tx = pin 10
 
 // Teensy 3.0 / Teensy 3.1
 #elif defined(__MK20DX128__) || defined(__MK20DX256__) || defined(__MK64FX512__) || defined(__MK66FX1M0__)
@@ -184,10 +146,6 @@
 
 #elif defined(ESP32)
 	#define IR_TIMER_USE_ESP32
-
-#elif defined(ARDUINO_ARCH_SAM) || defined(ARDUINO_ARCH_SAMD)
-	#define TIMER_PRESCALER_DIV 64
-
 #else
 // Arduino Duemilanove, Diecimila, LilyPad, Mini, Fio, Nano, etc
 // ATmega48, ATmega88, ATmega168, ATmega328
@@ -240,17 +198,17 @@
 
 //-----------------
 #if defined(CORE_OC2B_PIN)
-#	define SEND_PIN  CORE_OC2B_PIN  // Teensy
+#	define TIMER_PWM_PIN  CORE_OC2B_PIN  // Teensy
 #elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-#	define SEND_PIN  9              // Arduino Mega
+#	define TIMER_PWM_PIN  9              // Arduino Mega
 #elif defined(__AVR_ATmega1284__) || defined(__AVR_ATmega1284P__) \
 || defined(__AVR_ATmega644__) || defined(__AVR_ATmega644P__) \
 || defined(__AVR_ATmega324P__) || defined(__AVR_ATmega324A__) \
 || defined(__AVR_ATmega324PA__) || defined(__AVR_ATmega164A__) \
 || defined(__AVR_ATmega164P__)
-#	define SEND_PIN  14             // MightyCore
+#	define TIMER_PWM_PIN  14             // MightyCore
 #else
-#	define SEND_PIN  3              // Arduino Duemilanove, Diecimila, LilyPad, etc
+#	define TIMER_PWM_PIN  3              // Arduino Duemilanove, Diecimila, LilyPad, etc
 #endif					     // ATmega48, ATmega88, ATmega168, ATmega328
 
 //---------------------------------------------------------
@@ -293,22 +251,21 @@
 
 //-----------------
 #if defined(CORE_OC1A_PIN)
-#	define SEND_PIN  CORE_OC1A_PIN  // Teensy
+#	define TIMER_PWM_PIN  CORE_OC1A_PIN  // Teensy
 #elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-#	define SEND_PIN  11             // Arduino Mega
+#	define TIMER_PWM_PIN  11             // Arduino Mega
-#elif defined(__AVR_ATmega64__) || defined(__AVR_ATmega128__)
-#	define SEND_PIN  13	     // MegaCore
 #elif defined(__AVR_ATmega1284__) || defined(__AVR_ATmega1284P__) \
 || defined(__AVR_ATmega644__) || defined(__AVR_ATmega644P__) \
 || defined(__AVR_ATmega324P__) || defined(__AVR_ATmega324A__) \
 || defined(__AVR_ATmega324PA__) || defined(__AVR_ATmega164A__) \
 || defined(__AVR_ATmega164P__) || defined(__AVR_ATmega32__) \
-|| defined(__AVR_ATmega16__) || defined(__AVR_ATmega8535__)
+|| defined(__AVR_ATmega16__) || defined(__AVR_ATmega8535__) \
-#	define SEND_PIN  13             // MightyCore
+|| defined(__AVR_ATmega64__) || defined(__AVR_ATmega128__)
+#	define TIMER_PWM_PIN  13             // MightyCore, MegaCore
 #elif defined(__AVR_ATtiny84__)
-# 	define SEND_PIN  6
+# 	define TIMER_PWM_PIN  6
 #else
-#	define SEND_PIN  9              // Arduino Duemilanove, Diecimila, LilyPad, etc
+#	define TIMER_PWM_PIN  9              // Arduino Duemilanove, Diecimila, LilyPad, Sparkfun Pro Micro etc
 #endif					     // ATmega48, ATmega88, ATmega168, ATmega328
 
 //---------------------------------------------------------
@@ -340,11 +297,11 @@
 
 //-----------------
 #if defined(CORE_OC3A_PIN)
-#	define SEND_PIN  CORE_OC3A_PIN  // Teensy
+#	define TIMER_PWM_PIN  CORE_OC3A_PIN  // Teensy
-#elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
+#elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) || defined(ARDUINO_AVR_PROMICRO)
-#	define SEND_PIN  5              // Arduino Mega
+#	define TIMER_PWM_PIN  5              // Arduino Mega, Sparkfun Pro Micro
 #elif defined(__AVR_ATmega1284__) || defined(__AVR_ATmega1284P__)
-#	define SEND_PIN  6              // MightyCore
+#	define TIMER_PWM_PIN  6              // MightyCore
 #else
 #	error "Please add OC3A pin number here\n"
 #endif
@@ -355,12 +312,21 @@
 #elif defined(IR_USE_TIMER4_HS)
 
 #define TIMER_RESET
-#define TIMER_ENABLE_PWM    (TCCR4A |= _BV(COM4A1))
+
-#define TIMER_DISABLE_PWM   (TCCR4A &= ~(_BV(COM4A1)))
+#if defined(ARDUINO_AVR_PROMICRO) // Sparkfun Pro Micro                         
+	#define TIMER_ENABLE_PWM    (TCCR4A |= _BV(COM4A0))     // Use complimentary O̅C̅4̅A̅ output on pin 5
+	#define TIMER_DISABLE_PWM   (TCCR4A &= ~(_BV(COM4A0)))  // (Pro Micro does not map PC7 (32/ICP3/CLK0/OC4A)
+															// of ATmega32U4 )
+#else
+	#define TIMER_ENABLE_PWM    (TCCR4A |= _BV(COM4A1))
+	#define TIMER_DISABLE_PWM   (TCCR4A &= ~(_BV(COM4A1)))
+#endif
+
 #define TIMER_ENABLE_INTR   (TIMSK4 = _BV(TOIE4))
 #define TIMER_DISABLE_INTR  (TIMSK4 = 0)
 #define TIMER_INTR_NAME     TIMER4_OVF_vect
 
+
 #define TIMER_CONFIG_KHZ(val) ({ \
 	const uint16_t pwmval = SYSCLOCK / 2000 / (val); \
 	TCCR4A                = (1<<PWM4A); \
@@ -388,9 +354,11 @@
 
 //-----------------
 #if defined(CORE_OC4A_PIN)
-#	define SEND_PIN  CORE_OC4A_PIN  // Teensy
+#	define TIMER_PWM_PIN  CORE_OC4A_PIN  // Teensy
+#elif defined(ARDUINO_AVR_PROMICRO)
+#	define TIMER_PWM_PIN  5              // Sparkfun Pro Micro
 #elif defined(__AVR_ATmega32U4__)
-#	define SEND_PIN  13             // Leonardo
+#	define TIMER_PWM_PIN  13             // Leonardo
 #else
 #	error "Please add OC4A pin number here\n"
 #endif
@@ -424,9 +392,9 @@
 
 //-----------------
 #if defined(CORE_OC4A_PIN)
-#	define SEND_PIN  CORE_OC4A_PIN
+#	define TIMER_PWM_PIN  CORE_OC4A_PIN
 #elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-#	define SEND_PIN  6  // Arduino Mega
+#	define TIMER_PWM_PIN  6  // Arduino Mega
 #else
 #	error "Please add OC4A pin number here\n"
 #endif
@@ -460,9 +428,9 @@
 
 //-----------------
 #if defined(CORE_OC5A_PIN)
-#	define SEND_PIN  CORE_OC5A_PIN
+#	define TIMER_PWM_PIN  CORE_OC5A_PIN
 #elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-#	define SEND_PIN  46  // Arduino Mega
+#	define TIMER_PWM_PIN  46  // Arduino Mega
 #else
 #	error "Please add OC5A pin number here\n"
 #endif
@@ -529,7 +497,7 @@
 	CMT_MSC    = 0x03;            \
 })
 
-#define SEND_PIN  5
+#define TIMER_PWM_PIN  5
 
 // defines for TPM1 timer on Teensy-LC
 #elif defined(IR_USE_TIMER_TPM1)
@@ -559,7 +527,7 @@
 	FTM1_C0V = 0;                                \
 	FTM1_SC = FTM_SC_CLKS(1) | FTM_SC_PS(0) | FTM_SC_TOF | FTM_SC_TOIE; \
 })
-#define SEND_PIN        16
+#define TIMER_PWM_PIN        16
 
 // defines for timer_tiny0 (8 bits)
 #elif defined(IR_USE_TIMER_TINY0)
@@ -593,7 +561,7 @@
 })
 #endif
 
-#define SEND_PIN        1  /* ATtiny85 */
+#define TIMER_PWM_PIN        1  /* ATtiny85 */
 
 //---------------------------------------------------------
 // ESP32 (ESP8266 should likely be added here too)
@@ -610,29 +578,12 @@
 // way to do this on ESP32 is using the RMT built in driver like in this incomplete library below
 // https://github.com/ExploreEmbedded/ESP32_RMT
 #elif defined(IR_TIMER_USE_ESP32)
-
 #define TIMER_RESET	     
-
+#define TIMER_ENABLE_PWM     
-#ifdef ISR
+#define TIMER_DISABLE_PWM   Serial.println("IRsend not implemented for ESP32 yet");
-#	undef ISR
+#define TIMER_ENABLE_INTR    
-#endif
+#define TIMER_DISABLE_INTR   
-#define  ISR(f)  void IRTimer()
+#define TIMER_INTR_NAME      
-
-#elif defined(ARDUINO_ARCH_SAM) || defined(ARDUINO_ARCH_SAMD)
-// use timer 3 hardcoded at this time
-
-#define TIMER_RESET
-#define TIMER_ENABLE_PWM     // Not presently used
-#define TIMER_DISABLE_PWM
-#define TIMER_ENABLE_INTR    NVIC_EnableIRQ(TC3_IRQn) // Not presently used
-#define TIMER_DISABLE_INTR   NVIC_DisableIRQ(TC3_IRQn)
-#define TIMER_INTR_NAME      TC3_Handler // Not presently used
-#define TIMER_CONFIG_KHZ(f)
-
-#ifdef ISR
-#	undef ISR
-#endif
-#define  ISR(f)  void irs()
 
 //---------------------------------------------------------
 // Unknown Timer
@@ -641,13 +592,4 @@
 #	error "Internal code configuration error, no known IR_USE_TIMER# defined\n"
 #endif
 
-// Provide default definitions, portable but possibly slower than necessary.
-#ifndef SENDPIN_ON
-#define SENDPIN_ON(pin)  digitalWrite(pin, HIGH)
-#endif
-
-#ifndef SENDPIN_OFF
-#define SENDPIN_OFF(pin) digitalWrite(pin, LOW)
-#endif
-
 #endif // ! boarddefs_h

changelog.md

@@ -1,9 +1,3 @@
-## 2.5.0
-- Added Philips Extended RC-5 protocol support [PR #522] (https://github.com/z3t0/Arduino-IRremote/pull/522)
-
-## 2.4.0 - 2017/08/10
- - Cleanup of hardware dependencies. Merge in SAM support [PR #437](https://github.com/z3t0/Arduino-IRremote/pull/437)
-
 ## 2.3.3 - 2017/03/31
 - Added ESP32 IR receive support [PR #427](https://github.com/z3t0/Arduino-IRremote/pull/425)
 

examples/IRrecord/IRrecord.ino

@@ -45,7 +45,7 @@ int toggle = 0; // The RC5/6 toggle state
 // Most of this code is just logging
 void storeCode(decode_results *results) {
   codeType = results->decode_type;
-  int count = results->rawlen;
+  //int count = results->rawlen;
   if (codeType == UNKNOWN) {
     Serial.println("Received unknown code, saving as raw");
     codeLen = results->rawlen - 1;

examples/IRremoteInfo/IRremoteInfo.ino

@@ -79,7 +79,7 @@ void dumpTIMER() {
 
 void dumpTimerPin() {
   Serial.print(F("IR Tx Pin: "));
-  Serial.println(SEND_PIN);
+  Serial.println(TIMER_PWM_PIN);
 }
 
 void dumpClock() {

examples/IRtest/IRtest.ino

@@ -10,6 +10,7 @@
  */
 
 #include <IRremote.h>
+#include <IRremoteInt.h>
 
 // Dumps out the decode_results structure.
 // Call this after IRrecv::decode()

examples/IRtest2/IRtest2.ino

@@ -61,7 +61,7 @@ void setup()
 // Wait for the gap between tests, to synchronize with
 // the sender.
 // Specifically, wait for a signal followed by a gap of at last gap ms.
-void waitForGap(int gap) {
+void waitForGap(unsigned long gap) {
   Serial.println("Waiting for gap");
   while (1) {
     while (digitalRead(RECV_PIN) == LOW) { 
@@ -125,7 +125,7 @@ void dump(decode_results *results) {
 // The motivation behind this method is that the sender and the receiver
 // can do the same test calls, and the mode variable indicates whether
 // to send or receive.
-void test(char *label, int type, unsigned long value, int bits) {
+void test(const char *label, int type, unsigned long value, int bits) {
   if (mode == SENDER) {
     Serial.println(label);
     if (type == NEC) {
@@ -175,7 +175,7 @@ void test(char *label, int type, unsigned long value, int bits) {
 
 // Test raw send or receive.  This is similar to the test method,
 // except it send/receives raw data.
-void testRaw(char *label, unsigned int *rawbuf, int rawlen) {
+void testRaw(const char *label, unsigned int *rawbuf, int rawlen) {
   if (mode == SENDER) {
     Serial.println(label);
     irsend.sendRaw(rawbuf, rawlen, 38 /* kHz */);

examples/LGACSendDemo/LGACSendDemo.ino

@@ -192,12 +192,12 @@ void loop()
         ac_activate(AC_TEMPERATURE, AC_FLOW);
         break;
       case 2:
-        if ( b == 0 | b == 1 ) {
+        if ( b == 0 || b == 1 ) {
           ac_change_air_swing(b);
         }
         break;
       case 3: // 1  : clean on, power on
-        if ( b == 0 | b == 1 ) {
+        if ( b == 0 || b == 1 ) {
           ac_air_clean(b);
         }
         break;

examples/LegoPowerFunctionsSendDemo/LegoPowerFunctionsSendDemo.ino

@@ -4,6 +4,7 @@
  */
 
 #include <IRremote.h>
+#include <IRremoteInt.h>
 
 IRsend irsend;
 

irRecv.cpp

@@ -1,4 +1,10 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
+
+#ifdef IR_TIMER_USE_ESP32
+hw_timer_t *timer;
+void IRTimer(); // defined in IRremote.cpp
+#endif
 
 //+=============================================================================
 // Decodes the received IR message
@@ -84,6 +90,11 @@ int  IRrecv::decode (decode_results *results)
 	if (decodeLegoPowerFunctions(results))  return true ;
 #endif
 	
+#if DECODE_NERF_LOP
+	DBG_PRINTLN("Attempting Nerf Laser Ops Pro Functions");
+	if (decodeNerfLOP(results))  return true ;
+#endif
+
 	// decodeHash returns a hash on any input.
 	// Thus, it needs to be last in the list.
 	// If you add any decodes, add them before this.
@@ -114,10 +125,19 @@ IRrecv::IRrecv (int recvpin, int blinkpin)
 //+=============================================================================
 // initialization
 //
-#ifdef USE_DEFAULT_ENABLE_IR_IN
 void  IRrecv::enableIRIn ( )
 {
 // Interrupt Service Routine - Fires every 50uS
+#ifdef ESP32
+	// ESP32 has a proper API to setup timers, no weird chip macros needed
+	// simply call the readable API versions :)
+	// 3 timers, choose #1, 80 divider nanosecond precision, 1 to count up
+	timer = timerBegin(1, 80, 1);
+	timerAttachInterrupt(timer, &IRTimer, 1);
+	// every 50ns, autoreload = true
+	timerAlarmWrite(timer, 50, true);
+	timerAlarmEnable(timer);
+#else
 	cli();
 	// Setup pulse clock timer interrupt
 	// Prescale /8 (16M/8 = 0.5 microseconds per tick)
@@ -131,6 +151,7 @@ void  IRrecv::enableIRIn ( )
 	TIMER_RESET;
 
 	sei();  // enable interrupts
+#endif
 
 	// Initialize state machine variables
 	irparams.rcvstate = STATE_IDLE;
@@ -139,17 +160,14 @@ void  IRrecv::enableIRIn ( )
 	// Set pin modes
 	pinMode(irparams.recvpin, INPUT);
 }
-#endif // USE_DEFAULT_ENABLE_IR_IN
 
 //+=============================================================================
 // Enable/disable blinking of pin 13 on IR processing
 //
 void  IRrecv::blink13 (int blinkflag)
 {
-#ifdef BLINKLED
 	irparams.blinkflag = blinkflag;
 	if (blinkflag)  pinMode(BLINKLED, OUTPUT) ;
-#endif
 }
 
 //+=============================================================================

irSend.cpp

@@ -1,6 +1,6 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
-#ifdef SENDING_SUPPORTED
 //+=============================================================================
 void  IRsend::sendRaw (const unsigned int buf[],  unsigned int len,  unsigned int hz)
 {
@@ -15,59 +15,14 @@ void  IRsend::sendRaw (const unsigned int buf[],  unsigned int len,  unsigned in
 	space(0);  // Always end with the LED off
 }
 
-#ifdef USE_SOFT_CARRIER
-void inline IRsend::sleepMicros(unsigned long us)
-{
-#ifdef USE_SPIN_WAIT
-	sleepUntilMicros(micros() + us);
-#else
-	if (us > 0U) // Is this necessary? (Official docu https://www.arduino.cc/en/Reference/DelayMicroseconds does not tell.)
-		delayMicroseconds((unsigned int) us);
-#endif
-}
-
-void inline IRsend::sleepUntilMicros(unsigned long targetTime)
-{
-#ifdef USE_SPIN_WAIT
-	while (micros() < targetTime)
-		;
-#else
-        unsigned long now = micros();
-        if (now < targetTime)
-                sleepMicros(targetTime - now);
-#endif
-}
-#endif // USE_SOFT_CARRIER
-
 //+=============================================================================
 // Sends an IR mark for the specified number of microseconds.
 // The mark output is modulated at the PWM frequency.
 //
-
+void  IRsend::mark (unsigned int time)
-void IRsend::mark(unsigned int time)
 {
-#ifdef USE_SOFT_CARRIER
-	unsigned long start = micros();
-	unsigned long stop = start + time;
-	if (stop + periodTime < start)
-		// Counter wrap-around, happens very seldomly, but CAN happen.
-		// Just give up instead of possibly damaging the hardware.
-		return;
-
-	unsigned long nextPeriodEnding = start;
-	unsigned long now = micros();
-	while (now < stop) {
-		SENDPIN_ON(sendPin);
-		sleepMicros(periodOnTime);
-		SENDPIN_OFF(sendPin);
-		nextPeriodEnding += periodTime;
-		sleepUntilMicros(nextPeriodEnding);
-		now = micros();
-	}
-#else
 	TIMER_ENABLE_PWM; // Enable pin 3 PWM output
 	if (time > 0) custom_delay_usec(time);
-#endif
 }
 
 //+=============================================================================
@@ -99,16 +54,13 @@ void  IRsend::space (unsigned int time)
 //
 void  IRsend::enableIROut (int khz)
 {
-#ifdef USE_SOFT_CARRIER
+// FIXME: implement ESP32 support, see IR_TIMER_USE_ESP32 in boarddefs.h
-	periodTime = (1000U + khz/2) / khz; // = 1000/khz + 1/2 = round(1000.0/khz)
+#ifndef ESP32
-	periodOnTime = periodTime * DUTY_CYCLE / 100U - PULSE_CORRECTION;
-#endif
-	
 	// Disable the Timer2 Interrupt (which is used for receiving IR)
 	TIMER_DISABLE_INTR; //Timer2 Overflow Interrupt
 
-	pinMode(sendPin, OUTPUT);
+	pinMode(TIMER_PWM_PIN, OUTPUT);
-	SENDPIN_OFF(sendPin); // When not sending, we want it low
+	digitalWrite(TIMER_PWM_PIN, LOW); // When not sending PWM, we want it low
 
 	// COM2A = 00: disconnect OC2A
 	// COM2B = 00: disconnect OC2B; to send signal set to 10: OC2B non-inverted
@@ -116,6 +68,7 @@ void  IRsend::enableIROut (int khz)
 	// CS2  = 000: no prescaling
 	// The top value for the timer.  The modulation frequency will be SYSCLOCK / 2 / OCR2A.
 	TIMER_CONFIG_KHZ(khz);
+#endif
 }
 
 //+=============================================================================
@@ -135,4 +88,3 @@ void IRsend::custom_delay_usec(unsigned long uSecs) {
   //}
 }
 
-#endif // SENDING_SUPPORTED

ir_Aiwa.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                         AAA   IIIII  W   W   AAA

ir_Denon.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 // Reverse Engineered by looking at RAW dumps generated by IRremote
 

ir_Dish.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                       DDDD   IIIII   SSSS  H   H

ir_JVC.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                             JJJJJ  V   V   CCCC

ir_LG.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                               L       GGGG

ir_Lego_PF.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 #include "ir_Lego_PF_BitStreamEncoder.h"
 
 //==============================================================================

ir_Mitsubishi.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //    MMMMM  IIIII TTTTT   SSSS  U   U  BBBB   IIIII   SSSS  H   H  IIIII

ir_NEC.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                           N   N  EEEEE   CCCC

ir_NerfLaserOpsPro.cpp

@@ -0,0 +1,89 @@
+#include "IRremote.h"
+#include "IRremoteInt.h"
+
+//==============================================================================
+//
+//
+//                              NERF LASER OPS PRO
+//
+//
+//==============================================================================
+
+#define BITS          15  // The number of bits in the command
+
+#define HDR_MARK    2800  // The length of the Header:Mark
+#define HDR_SPACE   6000  // The lenght of the Header:Space
+
+#define ONE_MARK    1800  // The length of a Bit:Mark for 1's
+#define ZERO_MARK    800  // The length of a Bit:Mark for 0's
+#define ALL_SPACE   2100  // The length of a Bit:Space
+
+#define purpule 0x440
+#define red     0x400
+#define blue    0x420
+
+//+=============================================================================
+//
+#if SEND_NERF_LOP
+void  IRsend::sendNerfLOP (unsigned long data,  int nbits)
+{
+	// Set IR carrier frequency
+	enableIROut(40);
+
+	// Header
+	mark (HDR_MARK);
+	space(HDR_SPACE);
+  mark (HDR_MARK);
+
+	// Data
+	for (unsigned long  mask = 1UL << (nbits - 1);  mask;  mask >>= 1) {
+		if (data & mask) {
+      space(ALL_SPACE);
+			mark (ONE_MARK);
+		} else {
+			space(ALL_SPACE);
+			mark (ZERO_MARK);
+		}
+	}
+  
+  space(0);  // Always end with the LED off
+}
+#endif
+
+//+=============================================================================
+//
+#if DECODE_NERF_LOP
+bool  IRrecv::decodeNerfLOP (decode_results *results)
+{
+  //NOT IMPLEMENTED YET
+  return false;
+	unsigned long  data   = 0;  // Somewhere to build our code
+	int            offset = 1;  // Skip the Gap reading
+
+	// Check we have the right amount of data
+	if (irparams.rawlen != 1 + 2 + (2 * BITS) + 1)  return false ;
+
+	// Check initial Mark+Space match
+	if (!MATCH_MARK (results->rawbuf[offset++], HDR_MARK ))  return false ;
+	if (!MATCH_SPACE(results->rawbuf[offset++], HDR_SPACE))  return false ;
+
+	// Read the bits in
+	for (int i = 0;  i < SHUZU_BITS;  i++) {
+		// Each bit looks like: MARK + SPACE_1 -> 1
+		//                 or : MARK + SPACE_0 -> 0
+		if (!MATCH_MARK(results->rawbuf[offset++], BIT_MARK))  return false ;
+
+		// IR data is big-endian, so we shuffle it in from the right:
+		if      (MATCH_SPACE(results->rawbuf[offset], ONE_SPACE))   data = (data << 1) | 1 ;
+		else if (MATCH_SPACE(results->rawbuf[offset], ZERO_SPACE))  data = (data << 1) | 0 ;
+		else                                                        return false ;
+		offset++;
+	}
+
+	// Success
+	results->bits        = BITS;
+	results->value       = data;
+	results->decode_type = SHUZU;
+	return true;
+}
+#endif

ir_Panasonic.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //       PPPP    AAA   N   N   AAA    SSSS   OOO   N   N  IIIII   CCCC

ir_RC5_RC6.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //+=============================================================================
 // Gets one undecoded level at a time from the raw buffer.
@@ -77,73 +78,6 @@ void  IRsend::sendRC5 (unsigned long data,  int nbits)
 
 	space(0);  // Always end with the LED off
 }
-
-void  IRsend::sendRC5ext (unsigned long addr, unsigned long cmd, boolean toggle)
-{
-	// Set IR carrier frequency
-	enableIROut(36);
-	
-	unsigned long addressBits = 5;
-	unsigned long commandBits = 7;
-	unsigned long nbits = addressBits + commandBits;
-	
-	// Start
-	mark(RC5_T1);
-	
-	// Bit #6 of the command part, but inverted!
-	unsigned long cmdBit6 = (1UL << (commandBits-1)) & cmd;
-	if (cmdBit6) {
-		// Inverted (1 -> 0 = mark-to-space)
-		mark(RC5_T1);
-		space(RC5_T1);
-	} else {
-		space(RC5_T1);
-		mark(RC5_T1);
-	}
-	commandBits--;
-
-	// Toggle bit
-	static int toggleBit = 1;
-	if (toggle) {
-		if (toggleBit == 0) {
-			toggleBit = 1;
-		} else {
-			toggleBit = 0;
-		}
-	}
-	if (toggleBit) {
-		space(RC5_T1);
-		mark(RC5_T1);
-	} else {
-		mark(RC5_T1);
-		space(RC5_T1);
-	}
-
-	// Address
-	for (unsigned long  mask = 1UL << (addressBits - 1);  mask;  mask >>= 1) {
-		if (addr & mask) {
-			space(RC5_T1); // 1 is space, then mark
-			mark(RC5_T1);
-		} else {
-			mark(RC5_T1);
-			space(RC5_T1);
-		}
-	}
-	
-	// Command
-	for (unsigned long  mask = 1UL << (commandBits - 1);  mask;  mask >>= 1) {
-		if (cmd & mask) {
-			space(RC5_T1); // 1 is space, then mark
-			mark(RC5_T1);
-		} else {
-			mark(RC5_T1);
-			space(RC5_T1);
-		}
-	}
-
-	space(0);  // Always end with the LED off
-}
-
 #endif
 
 //+=============================================================================

ir_Samsung.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //              SSSS   AAA    MMM    SSSS  U   U  N   N   GGGG

ir_Sanyo.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                      SSSS   AAA   N   N  Y   Y   OOO

ir_Sharp.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                       SSSS  H   H   AAA   RRRR   PPPP

ir_Sony.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //                           SSSS   OOO   N   N  Y   Y

ir_Template.cpp

@@ -92,6 +92,7 @@ Regards,
 */
 
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //

ir_Whynter.cpp

@@ -1,4 +1,5 @@
 #include "IRremote.h"
+#include "IRremoteInt.h"
 
 //==============================================================================
 //               W   W  H   H  Y   Y N   N TTTTT EEEEE  RRRRR

library.json

@@ -7,7 +7,7 @@
     "type": "git",
     "url": "https://github.com/z3t0/Arduino-IRremote.git"
   },
-  "version": "2.4.0",
+  "version": "2.3.3",
   "frameworks": "arduino",
   "platforms": "atmelavr",
   "authors" :

library.properties

@@ -1,9 +1,9 @@
 name=IRremote
-version=2.4.0
+version=2.2.3
-author=shirriff, z3t0
+author=shirriff
-maintainer=z3t0
+maintainer=shirriff
 sentence=Send and receive infrared signals with multiple protocols
-paragraph=Find more information at https://github.com/z3t0/Arduino-IRremote
+paragraph=Send and receive infrared signals with multiple protocols
-category=Communication
+category=Signal Input/Output
-url=https://github.com/z3t0/Arduino-IRremote
+url=https://github.com/shirriff/Arduino-IRremote.git
 architectures=*

readmdFrench.md

@@ -0,0 +1,97 @@
+##  IRremote Library
+
+
+Cette bibliothèque vous permet d'envoyer et de recevoir des signaux infrarouges sur un Arduino.
+Des tutoriels et plus d'informations seront disponibles sur la page d'accueil officielle.
+
+## Version - 2.2.3
+
+## Installation
+1. Allez à la [Releases](https://github.com/z3t0/Arduino-IRremote/releases) page.
+2. Téléchargez la dernière version.
+3. Extraire le fichier zip
+4. Déplacez le dossier "IRremote" vers vos bibliothèques.
+5. Assurez-vous de supprimer Arduino_Root / libraries / RobotIRremote. Où Arduino_Root fait référence au répertoire d'installation d'Arduino. La bibliothèque RobotIRremote a des définitions similaires à IRremote et provoque des erreurs.
+
+
+## FAQ
+Je ne travaille pas correctement en utilisant Neopixels (aka WS2811 / WS2812 / WS2812B)
+Que vous utilisiez la librairie Adafruit Neopixel ou FastLED, les interruptions sont désactivées sur de nombreux processeurs bas de gamme comme les arduinos de base. À son tour, cela empêche le gestionnaire IR de s'exécuter quand il le faut. Il y a quelques solutions à ce processus, voir cette page de Marc MERLIN
+[cette page de Marc MERLIN](http://marc.merlins.org/perso/arduino/post_2017-04-03_Arduino-328P-Uno-Teensy3_1-ESP8266-ESP32-IR-and-Neopixels.html)
+
+
+## Conseils pris en charge
+
+- Teensy 1.0 / 1.0++ / 2.0 / 2++ / 3.0 / 3.1 / Teensy-LC; Crédits: @PaulStoffregen (Teensy Team)
+- Sanguino
+- ATmega8, 48, 88, 168, 328
+- ATmega8535, 16, 32, 164, 324, 644, 1284,
+- ATmega64, 128
+- ATtiny 84 / 85
+- ESP32 (recevoir seulement)
+- ESP8266 est basé sur un ancien code qui n'est pas très récent, mais cela fonctionne raisonnablement bien. Voir https://github.com/markszabo/IRremoteESP8266
+Sparkfun Pro Micro
+
+
+
+
+Nous sommes ouverts aux suggestions d'ajout de support pour les nouveaux tableaux, cependant, nous vous recommandons fortement de contacter votre fournisseur et de fournir un soutien de leur côté.
+
+
+## Spécifications matérielles
+
+
+| Carte/CPU                                                                | Envoyer Pin         | Compteurs         |
+|--------------------------------------------------------------------------|---------------------|-------------------|
+| [ATtiny84](https://github.com/SpenceKonde/ATTinyCore)                    | **6**               | **1**             |
+| [ATtiny85](https://github.com/SpenceKonde/ATTinyCore)                    | **1**               | **TINY0**         |
+| [ATmega8](https://github.com/MCUdude/MiniCore)                           | **9**               | **1**             |
+| Atmega32u4                                                               | 5, 9, **13**        | 1, 3, **4**       |
+| [ATmega48, ATmega88, ATmega168, ATmega328](https://github.com/MCUdude/MiniCore) | **3**, 9     | 1, **2**          |
+| [ATmega1284](https://github.com/MCUdude/MightyCore)                      | 13, 14, 6           | 1, **2**, 3       |
+| [ATmega164, ATmega324, ATmega644](https://github.com/MCUdude/MightyCore) | 13, **14**          | 1, **2**          |
+| [ATmega8535 ATmega16, ATmega32](https://github.com/MCUdude/MightyCore)   | **13**              | **1**             |
+| [ATmega64, ATmega128](https://github.com/MCUdude/MegaCore)               | **13**              | **1**             |
+| ATmega1280, ATmega2560                                                   | 5, 6, **9**, 11, 46 | 1, **2**, 3, 4, 5 |
+| [ESP32](http://esp32.net/)                                               | N/A (insupporté) | **1**             |
+| [Sparkfun Pro Micro](https://www.sparkfun.com/products/12640)            | 9, **5**, 5         | 1, **3**, 4_HS    |
+| [Teensy 1.0](https://www.pjrc.com/teensy/)                               | **17**              | **1**             |
+| [Teensy 2.0](https://www.pjrc.com/teensy/)                               | 9, **10**, 14       | 1, 3, **4_HS**    |
+| [Teensy++ 1.0 / 2.0](https://www.pjrc.com/teensy/)                       | **1**, 16, 25       | 1, **2**, 3       |
+| [Teensy 3.0 / 3.1](https://www.pjrc.com/teensy/)                         | **5**               | **CMT**           |
+| [Teensy-LC](https://www.pjrc.com/teensy/)                                | **16**              | **TPM1**          |
+
+
+## Patchs expérimentaux
+
+Voici les correctifs strictement pris en charge qui n'ont pas encore été intégrés. Si vous avez des questions, n'hésitez pas à demander ici. Si cela fonctionne, faites le nous savoir!
+
+[Arduino 101](https://github.com/z3t0/Arduino-IRremote/pull/481#issuecomment-311243146)
+
+Le tableau ci-dessus répertorie les temporisations actuellement supportées et les broches d'envoi correspondantes, beaucoup de ces broches supplémentaires sont ouvertes.
+
+
+## Utilisation
+- À faire TODO (Vérifier les exemples pour l'instant)
+
+
+## Contribution
+Si vous voulez contribuer à ce projet:
+- Signaler les bogues et les erreurs
+- Demander des améliorations
+- Créer des problèmes et tirer des requêtes
+- Parlez de cette bibliothèque à d'autres personnes
+- Contribuer de nouveaux protocoles
+Vérifiez ici [ici](Contributing.md) pour quelques guidelines
+
+
+## Contact
+Email: zetoslab@gmail.com
+Please only email me if it is more appropriate than creating an Issue / PR. I **will** not respond to requests for adding support for particular boards, unless of course you are the creator of the board and would like to cooperate on the project. I will also **ignore** any emails asking me to tell you how to implement your ideas. However, if you have a private inquiry that you would only apply to you and you would prefer it to be via email, by all means.
+
+## Contributeurs
+Check [here](Contributors.md)
+@Lsuperman735 French translation 
+
+## Copyright
+Copyright 2009-2012 Ken Shirriff

src/esp32.cpp

@@ -1,38 +0,0 @@
-#ifdef ESP32
-
-// This file contains functions specific to the ESP32.
-
-#include "IRremote.h"
-
-// "Idiot check"
-#ifdef USE_DEFAULT_ENABLE_IR_IN
-#error Must undef USE_DEFAULT_ENABLE_IR_IN
-#endif
-
-hw_timer_t *timer;
-void IRTimer(); // defined in IRremote.cpp, masqueraded as ISR(TIMER_INTR_NAME)
-
-//+=============================================================================
-// initialization
-//
-void  IRrecv::enableIRIn ( )
-{
-// Interrupt Service Routine - Fires every 50uS
-	// ESP32 has a proper API to setup timers, no weird chip macros needed
-	// simply call the readable API versions :)
-	// 3 timers, choose #1, 80 divider nanosecond precision, 1 to count up
-	timer = timerBegin(1, 80, 1);
-	timerAttachInterrupt(timer, &IRTimer, 1);
-	// every 50ns, autoreload = true
-	timerAlarmWrite(timer, 50, true);
-	timerAlarmEnable(timer);
-
-	// Initialize state machine variables
-	irparams.rcvstate = STATE_IDLE;
-	irparams.rawlen = 0;
-
-	// Set pin modes
-	pinMode(irparams.recvpin, INPUT);
-}
-
-#endif // ESP32

src/sam.cpp

@@ -1,101 +0,0 @@
-// Support routines for SAM processor boards
-
-#include "IRremote.h"
-
-#if defined(ARDUINO_ARCH_SAM) || defined(ARDUINO_ARCH_SAMD)
-
-// "Idiot check"
-#ifdef USE_DEFAULT_ENABLE_IR_IN
-#error Must undef USE_DEFAULT_ENABLE_IR_IN
-#endif
-
-//+=============================================================================
-// ATSAMD Timer setup & IRQ functions
-//
-
-// following based on setup from GitHub jdneo/timerInterrupt.ino
-
-static void setTimerFrequency(int frequencyHz)
-{
-	int compareValue = (SYSCLOCK / (TIMER_PRESCALER_DIV * frequencyHz)) - 1;
-	//Serial.println(compareValue);
-	TcCount16* TC = (TcCount16*) TC3;
-	// Make sure the count is in a proportional position to where it was
-	// to prevent any jitter or disconnect when changing the compare value.
-	TC->COUNT.reg = map(TC->COUNT.reg, 0, TC->CC[0].reg, 0, compareValue);
-	TC->CC[0].reg = compareValue;
-	//Serial.print("COUNT.reg ");
-	//Serial.println(TC->COUNT.reg);
-	//Serial.print("CC[0].reg ");
-	//Serial.println(TC->CC[0].reg);
-	while (TC->STATUS.bit.SYNCBUSY == 1);
-}
-
-static void startTimer()
-{
-	REG_GCLK_CLKCTRL = (uint16_t) (GCLK_CLKCTRL_CLKEN | GCLK_CLKCTRL_GEN_GCLK0 | GCLK_CLKCTRL_ID_TCC2_TC3);
-	while (GCLK->STATUS.bit.SYNCBUSY == 1); // wait for sync
-
-	TcCount16* TC = (TcCount16*) TC3;
-
-	TC->CTRLA.reg &= ~TC_CTRLA_ENABLE;
-	while (TC->STATUS.bit.SYNCBUSY == 1); // wait for sync
-
-	// Use the 16-bit timer
-	TC->CTRLA.reg |= TC_CTRLA_MODE_COUNT16;
-	while (TC->STATUS.bit.SYNCBUSY == 1); // wait for sync
-
-	// Use match mode so that the timer counter resets when the count matches the compare register
-	TC->CTRLA.reg |= TC_CTRLA_WAVEGEN_MFRQ;
-	while (TC->STATUS.bit.SYNCBUSY == 1); // wait for sync
-
-	// Set prescaler to 1024
-	//TC->CTRLA.reg |= TC_CTRLA_PRESCALER_DIV1024;
-	TC->CTRLA.reg |= TC_CTRLA_PRESCALER_DIV64;
-	while (TC->STATUS.bit.SYNCBUSY == 1); // wait for sync
-
-	setTimerFrequency(1000000 / USECPERTICK);
-	
-	// Enable the compare interrupt
-	TC->INTENSET.reg = 0;
-	TC->INTENSET.bit.MC0 = 1;
-
-	NVIC_EnableIRQ(TC3_IRQn);
-
-	TC->CTRLA.reg |= TC_CTRLA_ENABLE;
-	while (TC->STATUS.bit.SYNCBUSY == 1); // wait for sync
-}
-
-//+=============================================================================
-// initialization
-//
-
-void IRrecv::enableIRIn()
-{
-	// Interrupt Service Routine - Fires every 50uS
-	//Serial.println("Starting timer");
-	startTimer();
-	//Serial.println("Started timer");
-
-	// Initialize state machine variables
-	irparams.rcvstate = STATE_IDLE;
-	irparams.rawlen = 0;
-
-	// Set pin modes
-	pinMode(irparams.recvpin, INPUT);
-}
-
-void irs(); // Defined in IRRemote as ISR(TIMER_INTR_NAME)
-
-void TC3_Handler(void)
-{
-	TcCount16* TC = (TcCount16*) TC3;
-	// If this interrupt is due to the compare register matching the timer count
-	// we toggle the LED.
-	if (TC->INTFLAG.bit.MC0 == 1) {
-		TC->INTFLAG.bit.MC0 = 1;
-		irs();
-	}
-}
-
-#endif // defined(ARDUINO_ARCH_SAM) || defined(ARDUINO_ARCH_SAMD)