Added to changelog

Conflicts:
	IRremote.cpp
	IRremote.h
* Saves lots of precious ram
* Debug Improvement
* Minor refactoring
* Better Install Instructions
* Using F() Macro

Credits: @zt30 and @fab672000.
Merged PR: #109

IRremote.cpp

@@ -17,7 +17,6 @@
  * LG added by Darryl Smith (based on the JVC protocol)
  * Whynter A/C ARC-110WD added by Francesco Meschia
  */
-
 #include "IRremote.h"
 #include "IRremoteInt.h"
 
@@ -31,39 +30,39 @@ volatile irparams_t irparams;
 // Normally macros are used for efficiency
 #ifdef DEBUG
 int MATCH(int measured, int desired) {
-  Serial.print("Testing: ");
+  Serial.print(F("Testing: "));
   Serial.print(TICKS_LOW(desired), DEC);
-  Serial.print(" <= ");
+  Serial.print(F(" <= "));
   Serial.print(measured, DEC);
-  Serial.print(" <= ");
+  Serial.print(F(" <= "));
   Serial.println(TICKS_HIGH(desired), DEC);
   return measured >= TICKS_LOW(desired) && measured <= TICKS_HIGH(desired);
 }
 
 int MATCH_MARK(int measured_ticks, int desired_us) {
-  Serial.print("Testing mark ");
+  Serial.print(F("Testing mark "));
   Serial.print(measured_ticks * USECPERTICK, DEC);
-  Serial.print(" vs ");
+  Serial.print(F(" vs "));
   Serial.print(desired_us, DEC);
-  Serial.print(": ");
+  Serial.print(F(": "));
   Serial.print(TICKS_LOW(desired_us + MARK_EXCESS), DEC);
-  Serial.print(" <= ");
+  Serial.print(F(" <= "));
   Serial.print(measured_ticks, DEC);
-  Serial.print(" <= ");
+  Serial.print(F(" <= "));
   Serial.println(TICKS_HIGH(desired_us + MARK_EXCESS), DEC);
   return measured_ticks >= TICKS_LOW(desired_us + MARK_EXCESS) && measured_ticks <= TICKS_HIGH(desired_us + MARK_EXCESS);
 }
 
 int MATCH_SPACE(int measured_ticks, int desired_us) {
-  Serial.print("Testing space ");
+  Serial.print(F("Testing space "));
   Serial.print(measured_ticks * USECPERTICK, DEC);
-  Serial.print(" vs ");
+  Serial.print(F(" vs "));
   Serial.print(desired_us, DEC);
-  Serial.print(": ");
+  Serial.print(F(": "));
   Serial.print(TICKS_LOW(desired_us - MARK_EXCESS), DEC);
-  Serial.print(" <= ");
+  Serial.print(F(" <= "));
   Serial.print(measured_ticks, DEC);
-  Serial.print(" <= ");
+  Serial.print(F(" <= "));
   Serial.println(TICKS_HIGH(desired_us - MARK_EXCESS), DEC);
   return measured_ticks >= TICKS_LOW(desired_us - MARK_EXCESS) && measured_ticks <= TICKS_HIGH(desired_us - MARK_EXCESS);
 }
@@ -311,6 +310,74 @@ void IRsend::enableIROut(int khz) {
   // The top value for the timer.  The modulation frequency will be SYSCLOCK / 2 / OCR2A.
   TIMER_CONFIG_KHZ(khz);
 }
+/* Sharp and DISH support by Todd Treece ( http://unionbridge.org/design/ircommand )
+
+The Dish send function needs to be repeated 4 times, and the Sharp function
+has the necessary repeat built in because of the need to invert the signal.
+
+Sharp protocol documentation:
+http://www.sbprojects.com/knowledge/ir/sharp.htm
+
+Here are the LIRC files that I found that seem to match the remote codes
+from the oscilloscope:
+
+Sharp LCD TV:
+http://lirc.sourceforge.net/remotes/sharp/GA538WJSA
+
+DISH NETWORK (echostar 301):
+http://lirc.sourceforge.net/remotes/echostar/301_501_3100_5100_58xx_59xx
+
+For the DISH codes, only send the last for characters of the hex.
+i.e. use 0x1C10 instead of 0x0000000000001C10 which is listed in the
+linked LIRC file.
+*/
+
+void IRsend::sendSharpRaw(unsigned long data, int nbits) {
+  enableIROut(38);
+
+  // Sending codes in bursts of 3 (normal, inverted, normal) makes transmission
+  // much more reliable. That's the exact behaviour of CD-S6470 remote control.
+  for (int n = 0; n < 3; n++) {
+    for (int i = 1 << (nbits-1); i > 0; i>>=1) {
+      if (data & i) {
+        mark(SHARP_BIT_MARK);
+        space(SHARP_ONE_SPACE);
+      }
+      else {
+        mark(SHARP_BIT_MARK);
+        space(SHARP_ZERO_SPACE);
+      }
+    }
+    
+    mark(SHARP_BIT_MARK);
+    space(SHARP_ZERO_SPACE);
+    delay(40);
+
+    data = data ^ SHARP_TOGGLE_MASK;
+  }
+}
+
+// Sharp send compatible with data obtained through decodeSharp
+void IRsend::sendSharp(unsigned int address, unsigned int command) {
+  sendSharpRaw((address << 10) | (command << 2) | 2, 15);
+}
+
+void IRsend::sendDISH(unsigned long data, int nbits) {
+  enableIROut(56);
+  mark(DISH_HDR_MARK);
+  space(DISH_HDR_SPACE);
+  for (int i = 0; i < nbits; i++) {
+    if (data & DISH_TOP_BIT) {
+      mark(DISH_BIT_MARK);
+      space(DISH_ONE_SPACE);
+    }
+    else {
+      mark(DISH_BIT_MARK);
+      space(DISH_ZERO_SPACE);
+    }
+    data <<= 1;
+  }
+}
 
 IRrecv::IRrecv(int recvpin)
 {
@@ -441,71 +508,84 @@ int IRrecv::decode(decode_results *results) {
     return ERR;
   }
 #ifdef DEBUG
-  Serial.println("Attempting NEC decode");
+  Serial.println(F("Attempting NEC decode"));
 #endif
   if (decodeNEC(results)) {
     return DECODED;
   }
 #ifdef DEBUG
-  Serial.println("Attempting Sony decode");
+  Serial.println(F("Attempting Sony decode"));
 #endif
   if (decodeSony(results)) {
     return DECODED;
   }
 #ifdef DEBUG
-  Serial.println("Attempting Sanyo decode");
+  Serial.println(F("Attempting Sanyo decode"));
 #endif
   if (decodeSanyo(results)) {
     return DECODED;
   }
 #ifdef DEBUG
-  Serial.println("Attempting Mitsubishi decode");
+  Serial.println(F("Attempting Sharp decode"));
+#endif
+  if (decodeSharp(results)) {
+    return DECODED;
+  }
+#ifdef DEBUG
+  Serial.println(F("Attempting Mitsubishi decode"));
 #endif
   if (decodeMitsubishi(results)) {
     return DECODED;
   }
 #ifdef DEBUG
-  Serial.println("Attempting RC5 decode");
+  Serial.println(F("Attempting RC5 decode"));
 #endif  
   if (decodeRC5(results)) {
     return DECODED;
   }
 #ifdef DEBUG
-  Serial.println("Attempting RC6 decode");
+  Serial.println(F("Attempting RC6 decode"));
 #endif 
   if (decodeRC6(results)) {
     return DECODED;
   }
 #ifdef DEBUG
-    Serial.println("Attempting Panasonic decode");
+    Serial.println(F("Attempting Panasonic decode"));
 #endif 
     if (decodePanasonic(results)) {
         return DECODED;
     }
 #ifdef DEBUG
-    Serial.println("Attempting LG decode");
+    Serial.println(F("Attempting LG decode"));
 #endif 
     if (decodeLG(results)) {
         return DECODED;
     }
 #ifdef DEBUG
-    Serial.println("Attempting JVC decode");
+    Serial.println(F("Attempting JVC decode"));
 #endif 
     if (decodeJVC(results)) {
         return DECODED;
     }
 #ifdef DEBUG
-  Serial.println("Attempting SAMSUNG decode");
+  Serial.println(F("Attempting SAMSUNG decode"));
 #endif
   if (decodeSAMSUNG(results)) {
     return DECODED;
   }
 #ifdef DEBUG
-  Serial.println("Attempting Whynter decode");
+  Serial.println(F("Attempting Whynter decode"));
 #endif
   if (decodeWhynter(results)) {
     return DECODED;
   }
+// Aiwa RC-T501
+#ifdef DEBUG
+  Serial.println("Attempting Aiwa RC-T501 decode");
+#endif 
+  if (decodeAiwaRCT501(results)) {
+    return DECODED;
+  }
   // decodeHash returns a hash on any input.
   // Thus, it needs to be last in the list.
   // If you add any decodes, add them before this.
@@ -576,7 +656,7 @@ long IRrecv::decodeSony(decode_results *results) {
   // Some Sony's deliver repeats fast after first
   // unfortunately can't spot difference from of repeat from two fast clicks
   if (results->rawbuf[offset] < SONY_DOUBLE_SPACE_USECS) {
-    // Serial.print("IR Gap found: ");
+    // Serial.print(F("IR Gap found: "));
     results->bits = 0;
     results->value = REPEAT;
     results->decode_type = SANYO;
@@ -657,14 +737,7 @@ long IRrecv::decodeWhynter(decode_results *results) {
       data = (data << 1) | 1;
     } 
     else if (MATCH_SPACE(results->rawbuf[offset],WHYNTER_ZERO_SPACE)) {
-      data <<= 1;
-    } 
-    else {
-      return ERR;
-    }
-    offset++;
-  }
-  
+ 
   // trailing mark
   if (!MATCH_MARK(results->rawbuf[offset], WHYNTER_BIT_MARK)) {
     return ERR;
@@ -677,6 +750,59 @@ long IRrecv::decodeWhynter(decode_results *results) {
 }
 
 
+long IRrecv::decodeSharp(decode_results *results) {
+  long data = 0;
+  if (irparams.rawlen < 32) {
+    return ERR;
+  }
+
+  int offset = 0; // Dont skip first space, check its size
+  
+  if (results->rawbuf[offset] < SHARP_RPT_SPACE) {
+    // Serial.print("IR Gap found: ");
+    results->bits = 0;
+    results->value = REPEAT;
+    results->decode_type = SHARP;
+    return DECODED;
+  }
+  
+  offset++;
+  
+  while (offset + 1 < irparams.rawlen) {
+    if (!MATCH_MARK(results->rawbuf[offset], SHARP_BIT_MARK)) {
+      break;
+    }
+    offset++;
+    if (MATCH_SPACE(results->rawbuf[offset], SHARP_ONE_SPACE)) {
+      data = (data << 1) | 1;
+    } 
+    else if (MATCH_SPACE(results->rawbuf[offset], SHARP_ZERO_SPACE)) {
+      data <<= 1;
+    } 
+    else {
+      return ERR;
+    }
+    offset++;
+  }
+ 
+
+  if (data & 1 || !(data & 2)) {
+    return ERR;
+  }
+
+  // Success
+  results->bits = (offset - 1) / 2;
+  if (results->bits < 15) {
+    results->bits = 0;
+    return ERR;
+  }
+  
+  results->sharpAddress = (data >> 10) & 0b11111;
+  results->value = (data >> 2) & 0xff;
+  results->decode_type = SHARP;
+  return DECODED;
+}
+
 // I think this is a Sanyo decoder - serial = SA 8650B
 // Looks like Sony except for timings, 48 chars of data and time/space different
 long IRrecv::decodeSanyo(decode_results *results) {
@@ -687,13 +813,13 @@ long IRrecv::decodeSanyo(decode_results *results) {
   int offset = 0; // Skip first space
   // Initial space  
   /* Put this back in for debugging - note can't use #DEBUG as if Debug on we don't see the repeat cos of the delay
-  Serial.print("IR Gap: ");
+  Serial.print(F("IR Gap: "));
   Serial.println( results->rawbuf[offset]);
-  Serial.println( "test against:");
+  Serial.println(F("test against:"));
   Serial.println(results->rawbuf[offset]);
   */
   if (results->rawbuf[offset] < SANYO_DOUBLE_SPACE_USECS) {
-    // Serial.print("IR Gap found: ");
+    // Serial.print(F("IR Gap found: "));
     results->bits = 0;
     results->value = REPEAT;
     results->decode_type = SANYO;
@@ -743,7 +869,7 @@ long IRrecv::decodeSanyo(decode_results *results) {
 
 // Looks like Sony except for timings, 48 chars of data and time/space different
 long IRrecv::decodeMitsubishi(decode_results *results) {
-  // Serial.print("?!? decoding Mitsubishi:");Serial.print(irparams.rawlen); Serial.print(" want "); Serial.println( 2 * MITSUBISHI_BITS + 2);
+  // Serial.print(F("?!? decoding Mitsubishi:"));Serial.print(irparams.rawlen); Serial.print(F(" want ")); Serial.println( 2 * MITSUBISHI_BITS + 2);
   long data = 0;
   if (irparams.rawlen < 2 * MITSUBISHI_BITS + 2) {
     return ERR;
@@ -751,14 +877,14 @@ long IRrecv::decodeMitsubishi(decode_results *results) {
   int offset = 0; // Skip first space
   // Initial space  
   /* Put this back in for debugging - note can't use #DEBUG as if Debug on we don't see the repeat cos of the delay
-  Serial.print("IR Gap: ");
+  Serial.print(F("IR Gap: "));
   Serial.println( results->rawbuf[offset]);
-  Serial.println( "test against:");
+  Serial.println(F("test against:"));
   Serial.println(results->rawbuf[offset]);
   */
   /* Not seeing double keys from Mitsubishi
   if (results->rawbuf[offset] < MITSUBISHI_DOUBLE_SPACE_USECS) {
-    // Serial.print("IR Gap found: ");
+    // Serial.print(F("IR Gap found: "));
     results->bits = 0;
     results->value = REPEAT;
     results->decode_type = MITSUBISHI;
@@ -783,12 +909,12 @@ long IRrecv::decodeMitsubishi(decode_results *results) {
       data <<= 1;
     } 
     else {
-      // Serial.println("A"); Serial.println(offset); Serial.println(results->rawbuf[offset]);
+      // Serial.println(F("A")); Serial.println(offset); Serial.println(results->rawbuf[offset]);
       return ERR;
     }
     offset++;
     if (!MATCH_SPACE(results->rawbuf[offset], MITSUBISHI_HDR_SPACE)) {
-      // Serial.println("B"); Serial.println(offset); Serial.println(results->rawbuf[offset]);
+      // Serial.println(F("B")); Serial.println(offset); Serial.println(results->rawbuf[offset]);
       break;
     }
     offset++;
@@ -843,10 +969,10 @@ int IRrecv::getRClevel(decode_results *results, int *offset, int *used, int t1)
   }
 #ifdef DEBUG
   if (val == MARK) {
-    Serial.println("MARK");
+    Serial.println(F("MARK"));
   } 
   else {
-    Serial.println("SPACE");
+    Serial.println(F("SPACE"));
   }
 #endif
   return val;   
@@ -1117,6 +1243,65 @@ long IRrecv::decodeSAMSUNG(decode_results *results) {
   return DECODED;
 }
 
+/**
+ * Aiwa system
+ * Remote control RC-T501
+ * Lirc file http://lirc.sourceforge.net/remotes/aiwa/RC-T501 
+ *
+ */
+long IRrecv::decodeAiwaRCT501(decode_results *results) {
+  int data = 0;
+  int offset = 1; // skip first garbage read
+
+  // Check SIZE
+  if(irparams.rawlen < 2 * (AIWA_RC_T501_SUM_BITS) + 4) {
+    return ERR;
+  }
+  
+  // Check HDR
+  if(!MATCH_MARK(results->rawbuf[offset], AIWA_RC_T501_HDR_MARK)) {
+    return ERR;
+  }
+  offset++;
+
+  // Check HDR space
+  if(!MATCH_SPACE(results->rawbuf[offset], AIWA_RC_T501_HDR_SPACE)) {
+    return ERR;
+  }
+  offset++;
+
+  offset += 26; // skip pre-data - optional
+  while(offset < irparams.rawlen - 4) {
+    if(MATCH_MARK(results->rawbuf[offset], AIWA_RC_T501_BIT_MARK)) {
+      offset++;
+    } 
+    else {
+      return ERR;
+    }
+    
+    // ONE & ZERO
+    if(MATCH_SPACE(results->rawbuf[offset], AIWA_RC_T501_ONE_SPACE)) {
+      data = (data << 1) | 1;
+    } 
+    else if(MATCH_SPACE(results->rawbuf[offset], AIWA_RC_T501_ZERO_SPACE)) {
+      data <<= 1;
+    } 
+    else {
+      // End of one & zero detected
+      break;
+    }
+    offset++;
+  }
+  
+  results->bits = (offset - 1) / 2;
+  if(results->bits < 42) {
+    return ERR;
+  }
+  results->value = data;
+  results->decode_type = AIWA_RC_T501;
+  return DECODED;
+}
+
 /* -----------------------------------------------------------------------
  * hashdecode - decode an arbitrary IR code.
  * Instead of decoding using a standard encoding scheme
@@ -1171,71 +1356,5 @@ long IRrecv::decodeHash(decode_results *results) {
   return DECODED;
 }
 
-/* Sharp and DISH support by Todd Treece ( http://unionbridge.org/design/ircommand )
 
-The Dish send function needs to be repeated 4 times, and the Sharp function
-has the necessary repeat built in because of the need to invert the signal.
 
-Sharp protocol documentation:
-http://www.sbprojects.com/knowledge/ir/sharp.htm
-
-Here are the LIRC files that I found that seem to match the remote codes
-from the oscilloscope:
-
-Sharp LCD TV:
-http://lirc.sourceforge.net/remotes/sharp/GA538WJSA
-
-DISH NETWORK (echostar 301):
-http://lirc.sourceforge.net/remotes/echostar/301_501_3100_5100_58xx_59xx
-
-For the DISH codes, only send the last for characters of the hex.
-i.e. use 0x1C10 instead of 0x0000000000001C10 which is listed in the
-linked LIRC file.
-*/
-
-void IRsend::sendSharpRaw(unsigned long data, int nbits) {
-  enableIROut(38);
-
-  // Sending codes in bursts of 3 (normal, inverted, normal) makes transmission
-  // much more reliable. That's the exact behaviour of CD-S6470 remote control.
-  for (int n = 0; n < 3; n++) {
-    for (int i = 1 << (nbits-1); i > 0; i>>=1) {
-      if (data & i) {
-        mark(SHARP_BIT_MARK);
-        space(SHARP_ONE_SPACE);
-      }
-      else {
-        mark(SHARP_BIT_MARK);
-        space(SHARP_ZERO_SPACE);
-      }
-    }
-    
-    mark(SHARP_BIT_MARK);
-    space(SHARP_ZERO_SPACE);
-    delay(40);
-
-    data = data ^ SHARP_TOGGLE_MASK;
-  }
-}
-
-// Sharp send compatible with data obtained through decodeSharp
-void IRsend::sendSharp(unsigned int address, unsigned int command) {
-  sendSharpRaw((address << 10) | (command << 2) | 2, 15);
-}
-
-void IRsend::sendDISH(unsigned long data, int nbits) {
-  enableIROut(56);
-  mark(DISH_HDR_MARK);
-  space(DISH_HDR_SPACE);
-  for (int i = 0; i < nbits; i++) {
-    if (data & DISH_TOP_BIT) {
-      mark(DISH_BIT_MARK);
-      space(DISH_ONE_SPACE);
-    }
-    else {
-      mark(DISH_BIT_MARK);
-      space(DISH_ZERO_SPACE);
-    }
-    data <<= 1;
-  }
-}

IRremote.h

@@ -17,6 +17,13 @@
 #ifndef IRremote_h
 #define IRremote_h
 
+#if defined(ARDUINO) && ARDUINO >= 100
+#include <Arduino.h>
+#else
+#include <WProgram.h>
+#endif
+
+
 // The following are compile-time library options.
 // If you change them, recompile the library.
 // If DEBUG is defined, a lot of debugging output will be printed during decoding.
@@ -28,13 +35,15 @@
 // Results returned from the decoder
 class decode_results {
 public:
-  int decode_type; // NEC, SONY, RC5, UNKNOWN
+  int8_t decode_type; 	// NEC, SONY, RC5, UNKNOWN
+  int8_t bits; 			// Number of bits in decoded value
+  unsigned long value; 	// Decoded value
+
   union { // This is used for decoding Panasonic and Sharp data
     unsigned int panasonicAddress;
     unsigned int sharpAddress;
   };
-  unsigned long value; // Decoded value
-  int bits; // Number of bits in decoded value
+
   volatile unsigned int *rawbuf; // Raw intervals in .5 us ticks
   int rawlen; // Number of records in rawbuf.
 };
@@ -53,6 +62,8 @@ public:
 #define SAMSUNG 11
 #define LG 12
 #define WHYNTER 13
+#define Sharp 14
+#define AIWA_RC_T501 15
 #define UNKNOWN -1
 
 // Decoded value for NEC when a repeat code is received
@@ -72,6 +83,7 @@ private:
   int getRClevel(decode_results *results, int *offset, int *used, int t1);
   long decodeNEC(decode_results *results);
   long decodeSony(decode_results *results);
+  long decodeSharp(decode_results *results);
   long decodeSanyo(decode_results *results);
   long decodeMitsubishi(decode_results *results);
   long decodeRC5(decode_results *results);
@@ -81,6 +93,7 @@ private:
   long decodeJVC(decode_results *results);
   long decodeSAMSUNG(decode_results *results);
   long decodeWhynter(decode_results *results);
+  long decodeAiwaRCT501(decode_results *results);
   long decodeHash(decode_results *results);
   int compare(unsigned int oldval, unsigned int newval);
 
@@ -111,6 +124,7 @@ public:
   void sendSharpRaw(unsigned long data, int nbits);
   void sendPanasonic(unsigned int address, unsigned long data);
   void sendJVC(unsigned long data, int nbits, int repeat); // *Note instead of sending the REPEAT constant if you want the JVC repeat signal sent, send the original code value and change the repeat argument from 0 to 1. JVC protocol repeats by skipping the header NOT by sending a separate code value like NEC does.
+  void sendAiwaRCT501(int code);
   // private:
   void sendSAMSUNG(unsigned long data, int nbits);
   void enableIROut(int khz);

IRremoteInt.h

@@ -149,7 +149,7 @@
 #define SHARP_ZERO_SPACE 795
 #define SHARP_GAP 600000
 #define SHARP_TOGGLE_MASK 0x3FF
-#define SHARP_RPT_SPACE 3000
+#define SHARP_RPT_SPACE 950 // 40ms
 
 #define DISH_HDR_MARK 400
 #define DISH_HDR_SPACE 6100
@@ -190,6 +190,20 @@
 #define SHARP_BITS 15
 #define DISH_BITS 16
 
+// AIWA RC T501
+// Lirc file http://lirc.sourceforge.net/remotes/aiwa/RC-T501 
+#define AIWA_RC_T501_HZ 38
+#define AIWA_RC_T501_BITS 15
+#define AIWA_RC_T501_PRE_BITS 26
+#define AIWA_RC_T501_POST_BITS 1
+#define AIWA_RC_T501_SUM_BITS AIWA_RC_T501_PRE_BITS+AIWA_RC_T501_BITS+AIWA_RC_T501_POST_BITS
+#define AIWA_RC_T501_HDR_MARK 8800
+#define AIWA_RC_T501_HDR_SPACE 4500
+#define AIWA_RC_T501_BIT_MARK 500
+#define AIWA_RC_T501_ONE_SPACE 600
+#define AIWA_RC_T501_ZERO_SPACE 1700
+
+
 #define TOLERANCE 25  // percent tolerance in measurements
 #define LTOL (1.0 - TOLERANCE/100.) 
 #define UTOL (1.0 + TOLERANCE/100.) 

README.md

@@ -3,8 +3,9 @@ This library enables you to send and receive using infra-red signals on an ardui
 
 Check [here](http://shirriff.github.io/Arduino-IRremote/) for tutorials and more information.
 
-## Version - 1.00
+## Version - 1.01
 
+ 
 ## Installation
 1. Navigate to the [Releases](https://github.com/shirriff/Arduino-IRremote/releases) page.
 2. Download the latest release.

changelog.md

@@ -0,0 +1,13 @@
+# Change Log
+All notable changes to this project will be documented in this file.
+This project adheres to [Semantic Versioning](http://semver.org/).
+
+## [1.0.1] - 2015-03-08
+### Added
+- Support for Sharp Decoding
+- Support for Aiwa Decoding
+- Changelog documentation
+
+### Changed
+- Improved memory management in debugging
+- Use of F() macro saves RAM

examples/AiwaRCT501SendDemo/AiwaRCT501SendDemo.ino

@@ -0,0 +1,25 @@
+/*
+ * IRremote: IRsendDemo - demonstrates sending IR codes with IRsend
+ * An IR LED must be connected to Arduino PWM pin 3.
+ * Version 0.1 July, 2009
+ * Copyright 2009 Ken Shirriff
+ * http://arcfn.com
+ */
+
+#include "IRremote.h"
+
+#define POWER 0x7F80
+
+IRsend irsend;
+
+void setup() {
+  Serial.begin(9600);
+  Serial.println("Arduino Ready");
+}
+
+void loop() {
+  if (Serial.read() != -1) {
+    irsend.sendAiwaRCT501(POWER);
+    delay(60); // Optional
+  }
+}

examples/IRrecvDump/IRrecvDump.ino

@@ -49,11 +49,20 @@ void dump(decode_results *results) {
     Serial.print(results->panasonicAddress,HEX);
     Serial.print(" Value: ");
   }
+  else if (results->decode_type == SHARP) {	
+    Serial.print("Decoded SHARP - Address: ");
+    Serial.print(results->sharpAddress,HEX);
+    Serial.print(" Value: ");
+  }
   else if (results->decode_type == LG) {
      Serial.print("Decoded LG: ");
   }
   else if (results->decode_type == JVC) {
      Serial.print("Decoded JVC: ");
+  
+  }
+  else if (results->decode_type == AIWA_RC_T501) {
+    Serial.print("Decoded AIWA RC T501: ");
   }
   else if (results->decode_type == WHYNTER) {
      Serial.print("Decoded Whynter: ");

keywords.txt

@@ -48,5 +48,6 @@ SHARP LITERAL1
 PANASONIC LITERAL1
 JVC LITERAL1
 LG LITERAL1
+SHARP LITERAL1
 UNKNOWN	LITERAL1
 REPEAT	LITERAL1