bumped version in README

Credits: https://github.com/LarsWH
Excerpt from PR:
```
Hi,

I added support for 'RC5 extended' in order to make this project:
https://www.instructables.com/id/Remote-Control-for-Lava-mMotion-Swing-Mounting-Bra/

The modification is working nicely in this single application. It has
not been tested elsewhere.

(I am new to Git and this is my first pull request ever. So please
excuse me if I have messed something up)

Kind regards,
Lars
```

Merged #522

IRremote.h

@@ -270,6 +270,7 @@ class IRsend
 		//......................................................................
 #		if SEND_RC5
 			void  sendRC5        (unsigned long data,  int nbits) ;
+			void  sendRC5ext     (unsigned long addr, unsigned long cmd, boolean toggle);
 #		endif
 #		if SEND_RC6
 			void  sendRC6        (unsigned long data,  int nbits) ;

README.md

@@ -8,7 +8,7 @@ This library enables you to send and receive using infra-red signals on an Ardui
 
 Tutorials and more information will be made available on [the official homepage](http://z3t0.github.io/Arduino-IRremote/).
 
-## Version - 2.2.3
+## Version - 2.4.3
 
 ## Installation
 1. Navigate to the [Releases](https://github.com/z3t0/Arduino-IRremote/releases) page.
@@ -43,7 +43,7 @@ We are open to suggestions for adding support to new boards, however we highly r
 | [ATtiny84](https://github.com/SpenceKonde/ATTinyCore)                    | **6**               | **1**             |
 | [ATtiny85](https://github.com/SpenceKonde/ATTinyCore)                    | **1**               | **TINY0**         |
 | [ATmega8](https://github.com/MCUdude/MiniCore)                           | **9**               | **1**             |
-| Atmega32u4                                                               | 5, 9, **13**        | 1, 3, **4**       |
+| Atmega32u4                                                               | 5, **9**, 13        | 1, 3, **4**       |
 | [ATmega48, ATmega88, ATmega168, ATmega328](https://github.com/MCUdude/MiniCore) | **3**, 9     | 1, **2**          |
 | [ATmega1284](https://github.com/MCUdude/MightyCore)                      | 13, 14, 6           | 1, **2**, 3       |
 | [ATmega164, ATmega324, ATmega644](https://github.com/MCUdude/MightyCore) | 13, **14**          | 1, **2**          |

boarddefs.h

@@ -85,8 +85,8 @@
 // Teensy 2.0
 #elif defined(__AVR_ATmega32U4__)
 	//#define IR_USE_TIMER1   // tx = pin 14
-	//#define IR_USE_TIMER3   // tx = pin 9
-	#define IR_USE_TIMER4_HS  // tx = pin 10
+	#define IR_USE_TIMER3   // tx = pin 9
+	//#define IR_USE_TIMER4_HS  // tx = pin 10
 
 // Teensy 3.0 / Teensy 3.1
 #elif defined(__MK20DX128__) || defined(__MK20DX256__) || defined(__MK64FX512__) || defined(__MK66FX1M0__)

changelog.md

@@ -1,3 +1,6 @@
+## 2.4.3
+- Added Philips Extended RC-5 protocol support [PR #522] (https://github.com/z3t0/Arduino-IRremote/pull/522)
+
 ## 2.3.3 - 2017/03/31
 - Added ESP32 IR receive support [PR #427](https://github.com/z3t0/Arduino-IRremote/pull/425)
 

examples/IRrecord/IRrecord.ino

@@ -45,7 +45,7 @@ int toggle = 0; // The RC5/6 toggle state
 // Most of this code is just logging
 void storeCode(decode_results *results) {
   codeType = results->decode_type;
-  //int count = results->rawlen;
+  int count = results->rawlen;
   if (codeType == UNKNOWN) {
     Serial.println("Received unknown code, saving as raw");
     codeLen = results->rawlen - 1;

examples/IRtest2/IRtest2.ino

@@ -61,7 +61,7 @@ void setup()
 // Wait for the gap between tests, to synchronize with
 // the sender.
 // Specifically, wait for a signal followed by a gap of at last gap ms.
-void waitForGap(unsigned long gap) {
+void waitForGap(int gap) {
   Serial.println("Waiting for gap");
   while (1) {
     while (digitalRead(RECV_PIN) == LOW) { 
@@ -125,7 +125,7 @@ void dump(decode_results *results) {
 // The motivation behind this method is that the sender and the receiver
 // can do the same test calls, and the mode variable indicates whether
 // to send or receive.
-void test(const char *label, int type, unsigned long value, int bits) {
+void test(char *label, int type, unsigned long value, int bits) {
   if (mode == SENDER) {
     Serial.println(label);
     if (type == NEC) {
@@ -175,7 +175,7 @@ void test(const char *label, int type, unsigned long value, int bits) {
 
 // Test raw send or receive.  This is similar to the test method,
 // except it send/receives raw data.
-void testRaw(const char *label, unsigned int *rawbuf, int rawlen) {
+void testRaw(char *label, unsigned int *rawbuf, int rawlen) {
   if (mode == SENDER) {
     Serial.println(label);
     irsend.sendRaw(rawbuf, rawlen, 38 /* kHz */);

examples/LGACSendDemo/LGACSendDemo.ino

@@ -192,12 +192,12 @@ void loop()
         ac_activate(AC_TEMPERATURE, AC_FLOW);
         break;
       case 2:
-        if ( b == 0 || b == 1 ) {
+        if ( b == 0 | b == 1 ) {
           ac_change_air_swing(b);
         }
         break;
       case 3: // 1  : clean on, power on
-        if ( b == 0 || b == 1 ) {
+        if ( b == 0 | b == 1 ) {
           ac_air_clean(b);
         }
         break;

ir_RC5_RC6.cpp

@@ -78,6 +78,73 @@ void  IRsend::sendRC5 (unsigned long data,  int nbits)
 
 	space(0);  // Always end with the LED off
 }
+
+void  IRsend::sendRC5ext (unsigned long addr, unsigned long cmd, boolean toggle)
+{
+	// Set IR carrier frequency
+	enableIROut(36);
+	
+	unsigned long addressBits = 5;
+	unsigned long commandBits = 7;
+	unsigned long nbits = addressBits + commandBits;
+	
+	// Start
+	mark(RC5_T1);
+	
+	// Bit #6 of the command part, but inverted!
+	unsigned long cmdBit6 = (1UL << (commandBits-1)) & cmd;
+	if (cmdBit6) {
+		// Inverted (1 -> 0 = mark-to-space)
+		mark(RC5_T1);
+		space(RC5_T1);
+	} else {
+		space(RC5_T1);
+		mark(RC5_T1);
+	}
+	commandBits--;
+
+	// Toggle bit
+	static int toggleBit = 1;
+	if (toggle) {
+		if (toggleBit == 0) {
+			toggleBit = 1;
+		} else {
+			toggleBit = 0;
+		}
+	}
+	if (toggleBit) {
+		space(RC5_T1);
+		mark(RC5_T1);
+	} else {
+		mark(RC5_T1);
+		space(RC5_T1);
+	}
+
+	// Address
+	for (unsigned long  mask = 1UL << (addressBits - 1);  mask;  mask >>= 1) {
+		if (addr & mask) {
+			space(RC5_T1); // 1 is space, then mark
+			mark(RC5_T1);
+		} else {
+			mark(RC5_T1);
+			space(RC5_T1);
+		}
+	}
+	
+	// Command
+	for (unsigned long  mask = 1UL << (commandBits - 1);  mask;  mask >>= 1) {
+		if (cmd & mask) {
+			space(RC5_T1); // 1 is space, then mark
+			mark(RC5_T1);
+		} else {
+			mark(RC5_T1);
+			space(RC5_T1);
+		}
+	}
+
+	space(0);  // Always end with the LED off
+}
+
 #endif
 
 //+=============================================================================